Results 1 to 12 of 12
11-15-2004, 05:03 PM #1
Anyone looking to buy a 2.95 RR No-Slip Pulley?
I just swapped to a smaller pulley, anyone local want to by my old 2.95 Reichard Racing No-Slip Pulley? PM me.FOR SALE
Proud Member of the Mid-Atlantic Cobra Association
2003 Redfire Cobra Convertible 01/27/2003 #2064 of 5082
-480 RWHP 500 RWTQ-11.70 @118.46 MPH 1.67 60 ft.
-Bassani X-Pipes w/cats + Cat-back Exhaust-Pro 5.0 Shifter with MGW Handle-Steeda CAI
-Nitto 555R 315/35 17-SCT Tuner Dyno Tuned 2.76 Amazon Racing/BF No-Slip Pulley + Idler
-Gates 74 Belt-Eibach Pro Kit Springs w/ MM Spring Isolators in front-Maximum Motorsports Caster Camber Plates
-Maximum Motorsports Subframe Connectors-Maximum Motorsports IRS Bushings
-Fiori Firewall Adjuster and Quadrant-Centerforce DFX Clutch w/ Fidanza Flywheel-LDC Cooling Mod
11-15-2004, 10:07 PM #2
Can I swap it with my stock pulley..and no other mods necessary?Mike K
98 Cobra Chrome Yellow....GONE!
04 Cobra VERT SY...GONE!
09 Ford Shelby GT500 Vapor w/Black...GONE!
11 Ford Shelby GT500 Vert Kona Blue w/white stripes!
MODS: Bob's Autosport LCA, BMR Adj UCA, BMR Mounts for UCA and LCA, FRPP Springs, BMR Adj. PH Bar, BMR PHB Brace, Revan Racing HE w/Dual Fan, 3x reservoir, 170* T-Stat, 2.50 Pulley with 90mm idler, Jon Lund Tune on SCT X Cal 3, Aeroforce CNF Dual Gauges in SOS Dual A Pillar Pod, DSS Alum 1 Piece DS, MBRP Headers, MBRP Catless H-Pipe, FR 65mm TB, JLT Kona Blue 123mm CAI, Bob's Oil Separator, IW 10%, Ceramic Tint, complete front done with Paint Protection Film and TF Mach 6 brushed aluminum w/ chrome lips 20x9 20x11 with Nittos
Thanks to Van at Revan Racing and Bill Wise at BAP for parts and installation!
Proud Member of the Mid-Atlantic Cobra Association Member #15
11-15-2004, 10:46 PM #3Originally Posted by Cobra330Competition Speed and Sound
Hellion Power Systems
Full Tilt Boogie Racing
Speed of Sound
Speed Hut Custom Gauges
PM or give me a call for the best pricing
2006 Hot Rod Power Tour Dyno Challenge Champion
Comp O: 10.80 @ 128mph, 3.31 gears and 28" tires. Ported Eaton and 2.76 upper only. Solid axle
Turbo: 723rwhp/689rwtq, 22# mustang dyno. No track times with this setup
Built motor(281), FR500 cams, Eaton at 17#, longtubes. 570/565 SOLD
Tuned by Jon Lund
11-16-2004, 08:39 AM #4
Thanks for the help wutwine. Are you going to be at the Amazon Dyno day? I have some questions regarding this type of upgrade and what it might cost me..
11-16-2004, 11:15 AM #5
All you would need is a the pulley and a Predator Programmer (which is what I use) or a chip.
If I havn't sold it, I'll bring it on Saturday. I bought the pulley from Rick and he also pulled it off for me.
Btw, Where in Germantown are you? I live in Gaithersburg near the mall.
Last edited by RedfireVenom; 11-16-2004 at 11:17 AM.
11-16-2004, 11:41 AM #6Originally Posted by RedfireVenom
I am right at the corner of Great Seneca and Clopper. The Elms at Kingsview Village...is where I am at.
11-16-2004, 08:26 PM #7Originally Posted by RedfireVenom
Bring that pulley on Saturday..I should be there around noon..
11-18-2004, 08:34 PM #8
What time do you plan to be at Amazon?
11-19-2004, 08:27 AM #9Originally Posted by RedfireVenom
11-19-2004, 10:36 AM #10
Omar, do you want to go up early with the "first group"?.
2007 SHELBY GT500 - WHITE w/ BLUE STRIPES
Posi Ported Eaton w/2.40" Upper Pulley, CJ 65mm TB w/ L&M plenum, JLT 123 CAI, Magnaflow X Pipe/Axle Back, Blankenship tune, 3.73 FR gears, AFCO HE, DSS Aluminum Drive Shaft. (595 RWHP, 582 RWTQ)
2003 DSG COBRA - 10.88 @126.87 w/ 1.62 60' - SOLD......
6 Spd/IRS, Ported Eaton, 2.90/6 lb combo, JLP Tune, LT's, Dragon TB/Penum (529.41 RWHP, 513.76 RWTQ)
MID-ATLANTIC COBRA ASSOCIATION (MACA)
11-19-2004, 03:11 PM #11Originally Posted by IronTerp
11-19-2004, 06:07 PM #12
Omar, meeting at the Hillandale Safeway (New Hampshire Ave and I495) at 8:00. There should be like 4 of us going up then......