Results 1 to 12 of 12
  1. #1
    11 Second Vert Club RedfireVenom's Avatar
    Join Date
    February 2003
    Location
    Gaithersburg, Maryland
    Posts
    2,393

    Anyone looking to buy a 2.95 RR No-Slip Pulley?

    I just swapped to a smaller pulley, anyone local want to by my old 2.95 Reichard Racing No-Slip Pulley? PM me.
    FOR SALE

    Proud Member of the Mid-Atlantic Cobra Association

    2003 Redfire Cobra Convertible 01/27/2003 #2064 of 5082
    -480 RWHP 500 RWTQ-11.70 @118.46 MPH 1.67 60 ft.
    -Bassani X-Pipes w/cats + Cat-back Exhaust-Pro 5.0 Shifter with MGW Handle-Steeda CAI
    -Nitto 555R 315/35 17-SCT Tuner Dyno Tuned 2.76 Amazon Racing/BF No-Slip Pulley + Idler
    -Gates 74 Belt-Eibach Pro Kit Springs w/ MM Spring Isolators in front-Maximum Motorsports Caster Camber Plates
    -Maximum Motorsports Subframe Connectors-Maximum Motorsports IRS Bushings
    -Fiori Firewall Adjuster and Quadrant-Centerforce DFX Clutch w/ Fidanza Flywheel-LDC Cooling Mod

  2. #2
    FKNGFST Bonefish's Avatar
    Join Date
    September 2004
    Location
    Clarksburg, Maryland
    Posts
    7,912
    Can I swap it with my stock pulley..and no other mods necessary?
    Mike K

    Cobra/Shelby
    98 Cobra Chrome Yellow....GONE!
    04 Cobra Vert Screaming Yellow...GONE!
    09 Ford Shelby GT500 Vapor w/Black Stripes...GONE!
    11 Ford Shelby GT500 Vert Kona Blue w/White stripes!
    15 Ford Eplorer XLT Ingot Silver
    15 Hyundai Veloster Turbo R-Spec Elite White (Shared with the little woman...but mainly her's)

    MODS: 13/14 TVS & elbow Ported and painted KB, KB BAP, Bosch 72lb injectors, BPS 2.396 Pulley w/ 90mm aux idler, Low Lift 230 Cams, Bob's Autosport LCA, BMR Adj UCA, BMR Mounts for UCA and LCA, FRPP Springs, BMR Adj. PH Bar, BMR PHB Brace, Revan Racing HE w/Dual Fan, TF El Puto Coolant Tank in Satin Black with Engraved Bonefish/Cobra, 170* T-Stat, Lund Tune on SCT X Cal 4, Aeroforce CNF Dual Gauges in SOS Dual A Pillar Pod, DSS Alum 1 Piece DS, MBRP Headers, MBRP Catless H-Pipe, FR 65mm TB, JLT Kona Blue 123mm CAI, Bob's Oil Separator Passenger/Driver Side, Stifflers SFC and lower chassis brace, Ceramic Tint, complete front done with Paint Protection Film, Full Opti Coat Paint/Trim/Glass/Vert Top and TF Mach 6 brushed aluminum w/ chrome lips 20x9 20x11 with Nittos

    Thanks to Van at Revan Racing and Bill Wise at BAP for parts and installation! Big Thanks to JL II at Lund Racing for my tuning and Keith of Keiths Pit Stop for use of his dyno and help!

    Proud Member of the Mid-Atlantic Cobra Association Member #15

  3. #3
    Authorized Vendor TRBO VNM's Avatar
    Join Date
    February 2004
    Location
    Maryland
    Posts
    22,716
    Quote Originally Posted by Cobra330
    Can I swap it with my stock pulley..and no other mods necessary?
    yeah you can, but you would need a tune. either chip or flasher

  4. #4
    FKNGFST Bonefish's Avatar
    Join Date
    September 2004
    Location
    Clarksburg, Maryland
    Posts
    7,912
    Thanks for the help wutwine. Are you going to be at the Amazon Dyno day? I have some questions regarding this type of upgrade and what it might cost me..

  5. #5
    11 Second Vert Club RedfireVenom's Avatar
    Join Date
    February 2003
    Location
    Gaithersburg, Maryland
    Posts
    2,393
    All you would need is a the pulley and a Predator Programmer (which is what I use) or a chip.

    If I havn't sold it, I'll bring it on Saturday. I bought the pulley from Rick and he also pulled it off for me.

    Btw, Where in Germantown are you? I live in Gaithersburg near the mall.
    Last edited by RedfireVenom; 11-16-2004 at 10:17 AM.

  6. #6
    FKNGFST Bonefish's Avatar
    Join Date
    September 2004
    Location
    Clarksburg, Maryland
    Posts
    7,912
    Quote Originally Posted by RedfireVenom
    All you would need is a the pulley and a Predator Programmer (which is what I use) or a chip.

    If I havn't sold it, I'll bring it on Saturday. I bought the pulley from Rick and he also pulled it off for me.

    Btw, Where in Germantown are you? I live in Gaithersburg near the mall.

    Please do.

    I am right at the corner of Great Seneca and Clopper. The Elms at Kingsview Village...is where I am at.

  7. #7
    FKNGFST Bonefish's Avatar
    Join Date
    September 2004
    Location
    Clarksburg, Maryland
    Posts
    7,912
    Quote Originally Posted by RedfireVenom
    All you would need is a the pulley and a Predator Programmer (which is what I use) or a chip.

    If I havn't sold it, I'll bring it on Saturday. I bought the pulley from Rick and he also pulled it off for me.

    Btw, Where in Germantown are you? I live in Gaithersburg near the mall.
    I work near the mall though...I will have to look for you!

    Bring that pulley on Saturday..I should be there around noon..

  8. #8
    11 Second Vert Club RedfireVenom's Avatar
    Join Date
    February 2003
    Location
    Gaithersburg, Maryland
    Posts
    2,393
    What time do you plan to be at Amazon?

  9. #9
    FKNGFST Bonefish's Avatar
    Join Date
    September 2004
    Location
    Clarksburg, Maryland
    Posts
    7,912
    Quote Originally Posted by RedfireVenom
    What time do you plan to be at Amazon?
    Have to go to Tysons and be there at 10:30AM..to drop off a wing and then head up...I hope to be there around noon...

  10. #10
    Mid-Atlantic Cobra Assoc. IronTerp's Avatar
    Join Date
    November 2003
    Location
    State College, Pa
    Posts
    17,131
    Omar, do you want to go up early with the "first group"?
    .


    2007 SHELBY GT500 - 11.33 @121.14 w/ 1.62 60' @ 2,167 DA
    Posi Ported Eaton w/2.40" Upper Pulley, CJ 65mm TB w/ L&M plenum, JLT 123 CAI, Magnaflow X Pipe/Axle Back, 3.73 FR gears, AFCO HE, DSS Aluminum Drive Shaft. (586 RWHP, 569 RWTQ @ 18.5 timing)

    2003 DSG COBRA - 10.88 @126.87 w/ 1.62 60' - SOLD......
    6 Spd/IRS, Ported Eaton, 2.90/6 lb combo, JLP Tune, LT's, Dragon TB/Penum (529.41 RWHP, 513.76 RWTQ)


    MID-ATLANTIC COBRA ASSOCIATION (MACA)

  11. #11
    11 Second Vert Club RedfireVenom's Avatar
    Join Date
    February 2003
    Location
    Gaithersburg, Maryland
    Posts
    2,393
    Quote Originally Posted by IronTerp
    Omar, do you want to go up early with the "first group"?
    When is the first group leaving and from where?

  12. #12
    Mid-Atlantic Cobra Assoc. IronTerp's Avatar
    Join Date
    November 2003
    Location
    State College, Pa
    Posts
    17,131
    Omar, meeting at the Hillandale Safeway (New Hampshire Ave and I495) at 8:00. There should be like 4 of us going up then......

Similar Threads

  1. SC Pulley Slip vs Clutch Slip?
    By BigBeez03 in forum Terminator Talk
    Replies: 8
    Last Post: 05-23-2011, 03:03 PM
  2. Replies: 8
    Last Post: 11-22-2008, 12:01 AM
  3. Replies: 22
    Last Post: 05-29-2008, 02:22 PM
  4. Who runs a SFP non-slip 2.80" pulley? Does it slip or not?
    By BigDaddy in forum Terminator Archive
    Replies: 10
    Last Post: 12-24-2003, 01:12 AM
  5. SFPH non - slip pulley or RR non-slip pulley?
    By brasil in forum Terminator Archive
    Replies: 10
    Last Post: 08-26-2003, 11:02 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •