Results 1 to 9 of 9
03-11-2012, 10:45 PM #1
Is this okay? Heat checking?
It's on both drivers & pass rotors following a couple track days with HP+ pads. It's pretty narrow - the pads are wider than the ring you see in the pic.
I didn't really notice it until lately so I don't know if it was from last season or just recently as the car is out of winter storage (street usage).
I do the cool down laps and try not to let the car sit after I get into the pits (hard because HPDE1/2 makes you attend the drivers meeting right after the session).
Any negative impact?
thanks.Street/OT car: 97 Cobra –
Go: Bassani x-pipe and mufflers w/dumps, UD pullies, Tri-ax, CAI, MMR plenum spacer, 3.73s, FRPP Aluminum Driveshaft, Superior Axles W/ARP studs, Nitto 555s (275/315), Recaro Profi Seat
Turn: Nitto NT01 (275/275), MM SFC, MM CC plates, MM Panhard, MM LCA, MM Solid Steering Shaft, MM Solid Rack Bushings, Bilsteins, H&R Race Springs, Battle Boxes, '03/04 Cobra A-Arms.....MM TA and Super Race Springs still on the garage floor
Stop: SS Brake lines, Hawk Blues, Motul 600, Midcontinent Brake Ducts
Race car: #20 NASA CMC 94 GT
76 Scout II - SOLD &
03-12-2012, 07:56 AM #2
Looks fine to me. I'll get some pics later today of the rotor I just pulled off from my last event. It will show you what to look for.
03-12-2012, 08:04 AM #3
03-12-2012, 04:02 PM #4
Those are hot spots which are sort of typical if you don't season a rotor well enough, try to brake too much without the pads being bedded properly, throw too much heat into it too fast or simply overheated the rotor. Could be any combination of several things.
You should be able to work past that depending on the pad you're running. And with an HP+ I would think you could. Just make sure you have good brake cooling and don't overheat your brakes.
Unhappy with your SN-95 (1999-2004) Cobra IRS?
Got Wheel Hop, a leaking rear cover or a broken halfshaft?
Getting passed on the track by Corvettes?
This is how:
If you have questions after reading the FAQ on our site: http://www.fulltiltboogieracing.com/faqs.htm
shoot me a PM and I will answer them for you!
We also have a complete line of brake parts, brake conversion kits, one pc rotors, two pc rotors, fixed and floating, street pads, race pads along with suspension components for both SN-95 and S-197 vehicles.
Visit our web site for more information:
03-12-2012, 07:20 PM #5
Yeah, I don't see any cracks or heat checking. http://www.gunite.com/literature/pdf/discbrak.pdf
They usually radiate out. Like was mentiond, just hot pad residue. I had that happen to some street pads. Buffed it all off with a Scotch Brite pad on a drill. No biggie. Don't get carried away. I did take them off, so I could get to both sides. If you can get to both sides, leave on car and spin rotor as you buff. Took 15 mintues to do both sides, fronts.
Last edited by David Hester; 03-12-2012 at 07:31 PM.Dave Hester
2008 Roush 428R
Pro Challenge Mustang SCCA/SARRC SPU #14
03-12-2012, 08:24 PM #6
'98 SVT Mustang Cobra-NASA TTB *Retired to the street
'02 SVT Focus-only tracked a little
'01 Crown Vic Police Interceptor-Sold (and missed)
Videos on vimeo http://www.vimeo.com/user919253/videos
All cars are BAP Enhanced
Proud Member of the Mid-Atlantic Cobra Association
03-12-2012, 09:22 PM #7
They were brand new pads. I bedded them according to the instructions.
Brakes did "judder" when I was hard on the brakes following the long straight. I don't have brake ducts yet and it was really hot out so I'm sure they got pretty hot. Additionally, I had HPS pads in the rear so I figure they weren't providing any significant braking.
Sounds like it's not a huge deal - I'll buff them a little to see if that helps. I'm guessing it may be associated with My expert pad install/bedding .
So no expected poc/cracks on the pads?
rear hp+ pads are in hand with ducting coming soon
03-12-2012, 10:36 PM #8
HP+ are a good street/track day pad and ducts should help, but it may be time to step up a pad. As far as changing rears, if they weren't working, the rear discs would have... Pad shmearr on them, too. The HPS are made to work at lower temps, so they would have fried first... if they got that worked.
Last edited by David Hester; 03-12-2012 at 10:37 PM.
03-12-2012, 10:43 PM #9