Precision Turbo Cobra-Teksid-solid axle-900 hp

Turblown03

Member
Established Member
Joined
Aug 21, 2008
Messages
752
Location
Salt Lake City
Precision Turbo Cobra-Teksid-solid axle-1000 hp

Car makes 1000 hp, for some reason I can't change the main listing.

So I'm thinking of selling my car. Not a thing is wrong with this car and could be driven everyday if you wanted... Car just made (5-10-14) 1003 hp and 909 ftlbs on 110 octane, it makes 808 hp on pump gas, meth and about 19 psi... A/c blows ice cold and cruise works. Everything on the car works and does not leak any fluids at all. Title in hand.

Possible trades...... Let me know what you have. No Foxes unless it's a Termi Fox.

Car has gone 10.1 @ 145 mph (this was on 900hp) with an "ok" 60' in Salt Lake City which is 4200 ft.


It has 60,xxx miles and about 3,500 on turbo kit. The Precision is new!

YouTube vids added below.


Turbo kit extras are.........

It is the 76mm Hellion kit/Custom to accommodate the Precision
Billet Precision 7675 with CEA wheel
4" down pipe and 4" exhaust back to catback
PMAS blow thru MAF
Tial 50mm bov
Snow Meth injection kit
Turbo XS manual boost controller

Motor is...... 1500 miles

Teksid Block, 302 cubic inches
Freshly bored, honed, decked, and align honed
NEW *Diamond Pistons 8.5:1 Compression Ratio
NEW* Manley 4340 Pro-Series Forged H-Beam Rods
NEW* Kellogg Performance Forged, Polished Stroker Crankshaft (Balance and Magnafluxed)
New Total Seal Piston Rings
New ARP 2000-series Rod Bolts
New ARP Main Studs
New ARP Head Studs
New Federal Mogul Performance Rod and Main Bearings
New Melling Billet Oil Pump
New Factory Ford Water Pump
New MMR deep oil pan
New Ford Racing oil filter relocator
99 Cobra intake manifold and front cover
Canton crank case catch can

With the new motor build I had the front cover, valve covers, alternator and intake manifolds powder coated in wrinkle black.



Suspension:

Qa1 K member & A arms
MM coil overs and cc plates
MM full length subframe connectors
welded torque boxes
UPR rear coilovers with new Lakewood 50/50 drag shocks
Steeda Bump Steer Kit


Fuel:

Return style fuel system
80 lb injectors
Glens stainless sump tank
Twin Walbro 255 pumps
-8 feed line and -6 return
Aeromotive FPR
CPR Billet fuel rails anodized black

Drivetrain:

26 Spline input shaft and billet sleeve
Solid axle swap with welded housings
31 spline shafts
3" moroso wheel studs
Detroit Tru Trac
Metco upper and lower control arms
Metco diff cover with main cap studs
Ford racing 3:73 Gears
New Center Force DFX clutch
New Center Force Alu flywheel
Fresh build on trans (2000 miles)
MGW Orange handle short throw shifter
Steeda firewall adjuster and quadrant


Wheels/Tires:

XXR 535 18x9 front 18x10.5
New 335 Toyo Proxys

Interior/Electric:

Auto-meter Boost, fuel Ultra-light
AEM wideband
SOS dual gauge pillar
Raptor Shift light
MSD Launch Control 2 Step
SCT Excalibur tuner
Custom inner trunk lid cover "SVT"

Misc:

Polished Magnaflow catback
Billet hood vents
Tail lights are tinted
Windows are tinted
The fenders are rolled for the wider tires
Flat black cobra inserts in rear bumper

The roof is vinyl wrapped flat black so if you don't like it, it can be takin off very easy.

I know I'm forgetting a lot of stuff but if you have any questions just let me know, Thanks. Asking $29k... You can also reach me at 801-209-2172



Text is probably best.


81bc5710-07a1-4951-9f13-9c3e3842d4f2_zpsa5037ff2.jpg
[/URL]
image_zps772c980f.jpg

http://i138.photobucket.com/albums/q250/turblown94/image_zps536f54e8.jpg[/IMG][/URL]
IMG_0030_zpsae00da92.jpg

IMG_0014_zpsd9fa775e.jpg

011e5bd5aeaac8efd819a87a885fd9f495a881d139_zpsc207c02c.jpg

gold2_zpsbda50bc7.jpg


IMG_0033_zpsdffe3b55.jpg

image_zps00a2b715.jpg

IMG_0045_zps6ba29612.jpg

IMG_0034_zps9f370603.jpg



Iphone4356.jpg

Iphone4352.jpg

Iphone4350.jpg

Iphone4353.jpg

Iphone4177.jpg

Iphone4102.jpg

Iphone4313.jpg

Iphone4316.jpg

03Cobra004.jpg

03Cobra006.jpg

03Cobra011.jpg




VIDEO BELOW

th_011b109fddab7b7b32d7670f17c27e632199e6c0ad_zps7f1f311a.jpg
 
Last edited:

04-OW-COBRA

Member
Established Member
Joined
Jun 12, 2010
Messages
630
Location
Utah
Have seen this car run in person, clean and very quick car. GLWS Ben. Replacing it with anything?
 

Dasboot21

New Member
Established Member
Joined
Aug 8, 2009
Messages
9
Location
Utah
I can vouch for this car. Ive been around this car alot. Built very well, done right, clean car, well maintained. Pulls hard. Scary fast!
 

Turblown03

Member
Established Member
Joined
Aug 21, 2008
Messages
752
Location
Salt Lake City
Very nice.. Was the 10.1 pass on the 18s

The 10.1 pass was on 26"x11.50" MT Streets and 355s. Right after that race day I switched to 373s and 28"x11.50" MT Streets to dip into the 9s but the brand new slicks were like ice the first time out and I went 10.3 at 146mph with 1.7 60'. I couldn't get it to hook yet and I haven't been back to finish breaking in the new tires. :nonono:
 

Users who are viewing this thread



Top