• Welcome to SVTPerformance!

Terminator-Swap 1965 Mustang

Discussion in 'Classic Mustangs' started by EditorTurner, Oct 14, 2016.

  1. EditorTurner

    EditorTurner New Member Established Member

    Messages:
    1,049
    Joined:
    Oct 18, 2011
    Location:
    Lakeland, FL
    [​IMG]

    Challenge Accepted
    Sam Anderson challenged himself to build a 733-horsepower classic Mustang
    By Steve Turner
    Photos courtesy of Sam Anderson

    If you have built more than one project car, you always want to push the next one to a higher plane than the last. That was definitely the case for Sam Anderson, who set out to see just what kind of build he was capable of creating. As you can see, he was capable of fusing two iconic Mustangs into one project-car masterpiece.

    Obviously, the basis for Sam’s latest build was the 1965 Mustang you see here. An undeniable classic, this Mustang is still revered for its style, but not so much its performance. In the annals of Mustang performance there are a few milestone moments in the Mustang history books, but the car that started the horsepower heyday we are still living in today was the 2003 Cobra.

    “I wasn't really a big fan of older classics until I moved here to North Carolina and met a friend with a real nice ’69 Camaro,” Sam confessed. “That’s when I decided I wanted to build a badass hot rod. I had just the car in mind. A friend of mine in Wisconsin, where I'm from, had this ’65 fastback we actually tinkered with back in high school. It had been sitting ever since in his back yard, so I made a deal with him for it.”

    Known as the Terminator, the Special Vehicle Team’s 390-horsepower brute offered features that Mustang fans had craved for years—a supercharger, a six-speed manual transmission and an independent rear suspension. When Sam started setting forth the challenge for his classic Mustang project, it was the supercharged Four-Valve 4.6 and that T-56 six-speed manual transmission that fit the bill for modernizing the drivetrain of his ’65 ’Stang.

    “When I finally got the ’65 down south to start working on it, I had an ’03 Cobra as my current toy, and I knew it would be a perfect combo,” Sam said. “It is so hard to beat the reliability and driveability of the DOHC platform.”

    The blending of two Mustang eras in one car is no small task. Dropping in a wide modular like the Four-Valve 4.6 means cutting out the shock towers and installing a Mustang II-style front suspension. Sam turned to Rod & Custom Motorsports for the company’s full Mustang II front suspension to facilitate the swap.

    “The most challenging part really was trying to stay motivated,” he explained. “This build took a good bit of time and seeing such slow progress made it easy to get discouraged.”

    Sam was definitely up to the hardware challenge. However, he wasn’t just swapping in a stock Terminator engine. He put together a 284-cube engine with a blower-friendly 9.3:1 compression ratio. It wears custom cams and Fox Lake-ported heads and is topped with a VMP Performance Gen2 TVS supercharger. In short, it’s a stout combo that was in need of a custom calibration to allow it to run strong in a classic Mustang.

    For that calibration, Sam turned to tuning ace Dan Desio of Pro Dyno in Fort Mill, South Carolina. You can watch it run on the dyno, after Dan did his thing, right here…

    [video=youtube;5Pk_OcwjNFI]https://www.youtube.com/watch?v=5Pk_OcwjNFI[/video]

    “Dan did a great job with the tuning,” Sam enthused. “The driveability turned out even better than I expected with all the mods. Some cams seem to get tricky in this area and Dan nailed it.”

    After Dan worked his magic with the SCT Performance software, Sam’s project belted out an impressive 733 horsepower and 640 lb-ft of torque at the rear wheels. It produces those results with the VMP blower cranking out 18.5 pounds of boost, which has to be a blast in a lightweight classic Mustang.

    “After a few suspension tweaks and a shock change, it drives really well,” he said. “It was something I was nervous about during the whole build. I thought all this work and it will probably drive and ride like crap, but that's not the case. It’s really a blast to drive.”

    After finishing an epic build like this, Sam just plans to enjoy the fruits of his labors—at least until he gets the itch for another challenge.

    “It’s too early to think of the future plans for this car, but anything is possible!” he added.

    [​IMG]
    Sam Anderson is a fabricator from Mooresville, North Carolina, who challenged himself to create this stunning, Terminator-powered 1965 Mustang. It wears a striking Sherwin Williams Sonic Blue over Snow White Pearl paint scheme.

    [​IMG]
    The VMP TVS-blown Four-Valve under the hood looks just as good as the outside of the car as it follows the same white and Sonic Blue theme. A Howe aluminum radiator paired with a Lincoln Mark VIII electric fan keep the 733-horsepower Terminator engine cool.

    [​IMG]
    In back this 733-horsepower machine rolls on True Forged wheels wrapped in massive 345/30-18 BFGoodrich tires. Sam built the custom exhaust from the stepped headers to the X-pipe to the tailpipes, but the mufflers are off-the-shelf Magnaflows.

    [​IMG]
    Inside Sam upgraded his fastback with a custom rear-seat delete and a six-point roll cage painted in Sonic Blue to tie with the car’s two-tone paint job.

    [​IMG]
    Sam’s dash is full of Auto Meter and Aeroforce gauges that report on every facet of the car’s performance.

    The Mod List
    Powertrain
    Block: Teksid 4.6-liter aluminum, bored .020-inch over
    Crankshaft: Stock Terminator forged
    Rods: Manley H-beam
    Pistons: L&M-spec Diamond custom w/ L&M-spec Total Seal rings
    Camshafts: Bullet Racing Cams custom spec’d by Sam Anderson and Ed Schaider
    Cylinder Heads: Terminator Four-Valve w/ Fox Lake Stage 3 porting and Brian Tooley Racing valve springs
    Intake: Stock Terminator intercooled lower
    Power Adder: VMP Gen2 2.3-liter TVS supercharger w/ GT500 monoblade throttle body, SCT BA2600 mass air meter, JLT Performance cold-air intake, 3.2-inch blower pulley and custom caged 4-pound lower pulley by Claude Allen
    Fuel System: Two Walbro 255-lph fuel pumps w/ -8 fuel lines, Fore Innovations fuel rail, Injector Dynamics ID1000 fuel injectors and Fore Innovations fuel-pressure regulator
    Exhaust: Custom stepped 1.625x1.75x 3-inch long-tube headers by Sam Anderson w/ custom oval X-pipe, Magnaflow mufflers and stainless steel tailpipes
    Transmission: Tremec T-56 w/ 26-spline input shaft, an MGW shifter, a McLeod RXT clutch and a stock 2003 Cobra driveshaft
    Rearend: Shortened 9-inch w/ Eaton Tru-Trac differential, 3.89 gears and Moser axles

    Electronics
    Engine Management: Stock 2003 Cobra PCM w/ Ron Francis Telvorek panel
    and custom SCT calibration by Dan Desio at Pro Dyno
    Ignition: Stock Terminator

    Front Suspension
    K-member: R&C Mustang II coilover dual A-arm suspension
    A-arms: R&C Mustang II
    Shocks: Bilstein coilovers
    Springs: Eibach
    Brakes: Wilwood 13-inch w/ six-piston calipers
    Wheels: True Forged Formulas, 17-inch
    Tires: BFGoodrich, 215/45-17

    Rear Suspension
    Shocks: Bilstein
    Springs: Eibach
    Brakes: Wilwood 12-inch w/ four-piston calipers
    Wheels: True Forged Formula, 18-inch
    Tires: BFGoodrich, 345/30-18
     
  2. nofire

    nofire Sooner#65 Premium Member

    Messages:
    1,998
    Joined:
    Jul 5, 2006
    Location:
    Victorville, CA
    That is an AMAZING car.
     
  3. 03cobra#694

    03cobra#694 AKA Masta03 Staff Member Super Moderator

    Messages:
    38,849
    Joined:
    Aug 12, 2008
    Location:
    SW FL.
    That thing is sweet.
     
  4. MaCaNs

    MaCaNs Filth, Flarn, Filth Established Member

    Messages:
    964
    Joined:
    Jan 18, 2006
    Location:
    Baltimore
    wow! amazing job - car is absolutely sick!
     
  5. cj428mach

    cj428mach Premium Member Premium Member

    Messages:
    5,923
    Joined:
    Sep 21, 2012
    Location:
    Kansas
    Sam's a wonderful guy but his car really bugs me because it makes me really realize how low quality my own work is lol. The attention to detail on this car is amazing and I have no idea how anyone could build a car like of this caliber, it must take so much planning, skill and time to do it to this level.

    I bet this thing must be an absolute monster.
     
  6. cozmo2806

    cozmo2806 up in dat azz Established Member

    Messages:
    1,333
    Joined:
    Oct 15, 2007
    Location:
    28115
    Thanks for the props guys, I highly appreciate it. Also thanks to editor Turner for putting a great write up together as always.
     
  7. EditorTurner

    EditorTurner New Member Established Member

    Messages:
    1,049
    Joined:
    Oct 18, 2011
    Location:
    Lakeland, FL
    Thanks for your help, Sam. I'm glad you approve!


    Sent from my iPhone using Tapatalk
     
  8. Freakingstang

    Freakingstang New Member Established Member

    Messages:
    761
    Joined:
    Aug 2, 2009
    Location:
    Akron, OH
    This is sick man! I'm in the process of doing this to my 66 white coupe. I was considering patinting it sonic blue to match my cobra lol

    Did you have a build thread I missed? I'm doing the AJE colt 65 front end now

    Already have a narrowed 9" with a Detroit locker and 3.89's.

    How was the Ron Francias kit? I was looking into that or just going Holley
     
  9. Hammerglo

    Hammerglo New Member

    Messages:
    1
    Joined:
    Nov 30, 2016
    I too have a question or 3 for you about all of the wiring in the car and if you went with stand alone or made the factory terminator stuff work. Any help/ advice would be appreciated. Thank you
     
  10. PaxtonShelby

    PaxtonShelby Don't feed the ducks. They got disease. Established Member

    Messages:
    2,232
    Joined:
    Nov 16, 2010
    Location:
    Pittsburgh, PA
    Can't see the pics but I LOVE the car already! I'd love to be able to fit 345's under the rear of my '66! My 480+ rwhp is nuts in a vintage Mustang...I can't imagine what 700+ would be like!
     
  11. xhodzax

    xhodzax Member Established Member

    Messages:
    133
    Joined:
    Apr 23, 2013
    Location:
    minneapolis mn
    WOW awesome car man !
     
  12. BLKFOX

    BLKFOX Active Member Established Member

    Messages:
    1,324
    Joined:
    Apr 28, 2011
    Location:
    Indiana
    Good work!!
     

Share This Page