bassani axle backs 2014 GT

kingnut

New Member
Established Member
Joined
Mar 24, 2010
Messages
3,199
Location
NC
I love the sound of these. but can someone chime in about any drone issues these have. Also do they stick out on the 13-14 GT rear bumper?
 

91Gtturbo

Member
Established Member
Joined
Jun 3, 2007
Messages
43
Location
North Carolina
I just bought a set from a member here in the classifieds and they are going on my 13' tomorrow. I'll try and remember to report back with a picture and feedback.
 

Nuar

Active Member
Established Member
Joined
Jan 4, 2009
Messages
1,774
Location
Connecticut
There is no drone man... I had the competition catback that droned quite a bit, when I switched to the bassani axle backs and stock OTA pipes, it was a big relief to hear no drone :)
 

Code Vision

New Member
Established Member
Joined
Jun 10, 2013
Messages
9
Location
Maryland
Not sure if this applies, but I have the catback by bassani on my 2013 GT. For me the drone is actually kind of loud. I personally don't mind it, but it's there. The sound is so awesome that it's worth it though.

They don't stick out too far at all, looks just right to me.

I'm sure you've seen a ton of vids already, but these are mine. I would say get them.

2013 Mustang GT - Bassani Cat Back - YouTube
 

Nuar

Active Member
Established Member
Joined
Jan 4, 2009
Messages
1,774
Location
Connecticut
They don't stick out far at all.

IMAG0805_zps74a43035.jpg


IMAG0804_zps529d2f38.jpg


Here is a sound clip of cruising, yes its offroad, but all that did was make it a little louder, they didn't drone before that either.
I actually love these mufflers now, not too loud at all if you don't want them to be.

[youtube_browser]w7s3IccHluQ[/youtube_browser]

Thats what they looked like before the boss diffuser in case you were wondering.

[youtube_browser]W85OGri3wzA[/youtube_browser]
 
Last edited:

kingnut

New Member
Established Member
Joined
Mar 24, 2010
Messages
3,199
Location
NC
Thanks for all the replies. One more thing. Do these need to be welded on or are they a clamp on setup?
 

kingnut

New Member
Established Member
Joined
Mar 24, 2010
Messages
3,199
Location
NC
they do stick out further than i would like. but not nearly as bad as some i have seen. it looks like they could be shortened a couple of inches if they were cut and welded from the chamber to the tips. im probably gonna get them and do that. i will let yall know how they turn out.
 

kingnut

New Member
Established Member
Joined
Mar 24, 2010
Messages
3,199
Location
NC
be-5011r5_3133.jpg


if you look at this picture here. you can see what im talking about. from where the hanger is to the tips could be cut out.
 

Nuar

Active Member
Established Member
Joined
Jan 4, 2009
Messages
1,774
Location
Connecticut
Yup mine look the same. I suppose they could be cut down, but i want my tips to stick out past the bumper a little. I hate it when the exhaust smokes up the bumper above the tips.
 

kingnut

New Member
Established Member
Joined
Mar 24, 2010
Messages
3,199
Location
NC
Yup mine look the same. I suppose they could be cut down, but i want my tips to stick out past the bumper a little. I hate it when the exhaust smokes up the bumper above the tips.

i dont think it would be to much of a problem. the stock mufflers sit back pretty far.
 

kingnut

New Member
Established Member
Joined
Mar 24, 2010
Messages
3,199
Location
NC
anyone know where to find the best deal on these? i have found them for $475 new shipped.
 

Users who are viewing this thread



Top