jose21

New Member
Established Member
Joined
Mar 21, 2015
Messages
76
Location
California
I'm currently at 500rwhp and 470rwtq I'm trying to hit around 600 or close to it with stock supercharger
 

stroked mach

New Member
Established Member
Joined
Mar 1, 2012
Messages
744
Location
kntucky
spray all the way the motor is good for it and it will not be hard on the motor all the time like a big blower and cheeper
 

jose21

New Member
Established Member
Joined
Mar 21, 2015
Messages
76
Location
California
Alright thanks for the help looks like ima have to go with nitrous as much as didn't looks like the only way to get there and yea that's my signature lol
 

03' White Snake

Well-Known Member
Established Member
Joined
Feb 5, 2007
Messages
3,792
Location
Mass
You will not make 600 hp with a stock blower. Even spraying a shit ton of nitrous. The blower is just not efficient enough to move that amount of air.

You can make mid 500 hp with nitrous and a ported eaton.
 

Zemedici

Well-Known Member
Established Member
Joined
Jan 7, 2013
Messages
21,223
Location
Atlanta, GA
You will not make 600 hp with a stock blower. Even spraying a shit ton of nitrous. The blower is just not efficient enough to move that amount of air.

You can make mid 500 hp with nitrous and a ported eaton.

bullshit. You can make easily 600+ with nitrous.

http://www.modularfords.com/threads/64886-Nitrous-Eaton-combo/page3

Guy made 578 whp and over 730 tq on a 75 shot. There's guys running 150 and 200 shots. You're saying they wont make 20 hp? Come on.

Guys run a ported eaton and a small shot and are in the 10s all day every day.
 
Last edited:

CobraBob

Authorized Vendor
Established Member
Premium Member
Single Barrel Sirs
Joined
Nov 17, 2002
Messages
105,354
Location
Cheshire, CT
Alright thanks for the help looks like ima have to go with nitrous as much as didn't looks like the only way to get there and yea that's my signature lol
Shorten your signature because one of the mods will soon nail you for it. That's really long. Try removing the line breaks in between and go with one font size smaller. That should work.

I wish you the best trying to get 600hp out of an Eaton setup. Have you considered a Whipple, VMP or Kenne Bell? More expensive, but an easier, safer and more reliable route to take, if done right.
 

SvtChris03

New Member
Established Member
Joined
Mar 20, 2015
Messages
19
Location
San Mateo California
Hey, I am not sure if this has been covered already, but with the stock blower, 600 hp is pretty hard to achieve, and if it was done, the blower would not be able to withstand that type of power. I think even with a stage 6 port and 2.76 pulleys, bolt ons, and a dyno tune will have you shy of 600 but still not at 600. At that point, i would just say get a whipple 2.3 and get that 600hp like it is nothing, but then again, not all of us have that type of money to spend after we spent so much money already on our terminators lol.
 

Zemedici

Well-Known Member
Established Member
Joined
Jan 7, 2013
Messages
21,223
Location
Atlanta, GA
Hey, I am not sure if this has been covered already, but with the stock blower, 600 hp is pretty hard to achieve, and if it was done, the blower would not be able to withstand that type of power. I think even with a stage 6 port and 2.76 pulleys, bolt ons, and a dyno tune will have you shy of 600 but still not at 600. At that point, i would just say get a whipple 2.3 and get that 600hp like it is nothing, but then again, not all of us have that type of money to spend after we spent so much money already on our terminators lol.

Read the thread.....it can and has been done for years and years with nitrous. Easily.
 

03' White Snake

Well-Known Member
Established Member
Joined
Feb 5, 2007
Messages
3,792
Location
Mass
bullshit. You can make easily 600+ with nitrous.

http://www.modularfords.com/threads/64886-Nitrous-Eaton-combo/page3

Guy made 578 whp and over 730 tq on a 75 shot. There's guys running 150 and 200 shots. You're saying they wont make 20 hp? Come on.

Guys run a ported eaton and a small shot and are in the 10s all day every day.

578 is not 600 now is it. The eaton is just too small to move that volume of air. Run your engine that hard and spray a 200 shot. I'll be reading about you crying about blowing up your engine right off the dyno.

I don't care how fast a nitrous car and an eaton is. His thread is about 600 hp, not time slips.

A TS, is the correct way to make that power and have it reliable.
 

jose21

New Member
Established Member
Joined
Mar 21, 2015
Messages
76
Location
California
So I was able to make my signature smaller and 600 hp is alot to ask from stock blower but can it be done without nitrous I don't wanna harm the engine if anything I'll just have to save up to buy a bigger blower
 

b_dike

Active Member
Established Member
Joined
Jun 1, 2011
Messages
1,615
Location
Kansas City, MO
So I was able to make my signature smaller and 600 hp is alot to ask from stock blower but can it be done without nitrous I don't wanna harm the engine if anything I'll just have to save up to buy a bigger blower

NO!!! The eaton ported or not will NOT make 600rwhp without nitrous.

Upper/lower pullies, Port, and E85 will probably get you to 550 or so... Nitrous will get you the rest of the way and then some.
 

Hostlntent

Member
Established Member
Joined
Aug 11, 2012
Messages
116
Location
Colorado
A lot of folks are intimidated with Nitrous but if its tuned properly and you school yourself on how it works with the delivery options you have etc.. you may be surprised and glad you did it; now granted its not for everyone; I was hesitant at first but I'm glad I did it and haven't looked back ever since. if anything you could get you a system and have it in your arsenal to add in conjunction with a bigger blower down the road?
 

Users who are viewing this thread



Top