N/A builds

Supreme_5oh

New Member
Established Member
Joined
Aug 14, 2018
Messages
24
Location
Albuquerque, New Mexico
What are you guys N/A builds, I would like to see if theirs any variety in set ups? and what your hp and tq numbers are?
Also without boost or nitrous, what else can you do to the coyote engine to get more hp? after, intake manifold, cold air, e85, exhaust, and cams?
I myself have a Holley intake manifold, Pmas cold air, Texas speed headers and e85 and sitting @ 450WHP.
 

DMassey

No Habla Jibber Jabber
Established Member
Joined
Feb 16, 2005
Messages
1,920
Location
Boone Co, WV
I always wanted to throw a set of L&M intake cams in a Gen2 motor, but we ended up just getting a 2018. I'm waiting to see if L&M is going to do a set of Gen3 cams or not. I'll likely have Brett Barber port my intake manifold and decide if I want to port my stock tb or go with the Bullitt tb whenever it gets released.
 

Revvv

Infinity Poster
Established Member
Joined
Dec 8, 2017
Messages
10,189
Location
GA
Port and polish the heads, install a larger throttle body and plenum, empty the long block and bore and stroke the engine. Add cams, change injectors, and have fun.

Sent from my SM-G930V using the svtperformance.com mobile app
 

Supreme_5oh

New Member
Established Member
Joined
Aug 14, 2018
Messages
24
Location
Albuquerque, New Mexico
I always wanted to throw a set of L&M intake cams in a Gen2 motor, but we ended up just getting a 2018. I'm waiting to see if L&M is going to do a set of Gen3 cams or not. I'll likely have Brett Barber port my intake manifold and decide if I want to port my stock tb or go with the Bullitt tb whenever it gets released.

Adding a set of cams to a 2018 would be pretty interesting to see, since ive seen them go over 500whp FBO on e85 without cams, i have a local guy her that FBO did only put about 455whp, which is pretty low for a gen 3
 

Supreme_5oh

New Member
Established Member
Joined
Aug 14, 2018
Messages
24
Location
Albuquerque, New Mexico
Port and polish the heads, install a larger throttle body and plenum, empty the long block and bore and stroke the engine. Add cams, change injectors, and have fun.

Sent from my SM-G930V using the svtperformance.com mobile app[/QUOTE

I have yet to see any N/A 5.0s that have ported heads or bore and stroke engines, i wonder if anyone has done it and how much whp have they gained for that amount of cash...
 

Growlar

Member
Established Member
Joined
Jan 19, 2014
Messages
34
Location
Yorktown In
I think the engine flows great as it is ...i'd really like to see is a stock engine flung out to 9k rpms and see if i'm right..my bet is the curve keeps rising
 

Supreme_5oh

New Member
Established Member
Joined
Aug 14, 2018
Messages
24
Location
Albuquerque, New Mexico
update I swapped to CJ Manifold, and made 448 whp
last set up was Holley intake manifold, PMAS cold air, ts long tubes, e85, made 450whp and 367tq, with the CJ set up and FP cold air it made 448whp and 391 tq, what do you guys think, I would of thought the CJ would out perform the holley by a lot..
 

mikengail

Member
Established Member
Joined
Oct 26, 2012
Messages
138
Location
Albuquerque, NM
update I swapped to CJ Manifold, and made 448 whp
last set up was Holley intake manifold, PMAS cold air, ts long tubes, e85, made 450whp and 367tq, with the CJ set up and FP cold air it made 448whp and 391 tq, what do you guys think, I would of thought the CJ would out perform the holley by a lot..

2rwhp difference is around .4%. I don't know exactly how reliable the Dynojet is at Dyno Edge, but .4% would be well within anyone's margin of error, assuming a confidence level of 99% in the accuracy of the dyno. The actual curves of both rwtq and rwhp are probably more telling in any comparison of the two runs. At 5530' altitude, those numbers are not too shabby for a Gen2 Coyote. Even with SAE correction, the corrected results become much less accurate above 3000' altitude anyway. Lastly, the local E85 brew in the Albuquerque area has been testing around E65 for me. Welcome to gear head life at a mile high. Nevertheless, I think it would be much more interesting to compare those two intake manifolds with the VMP 67 TB and an '18+ GT intake with the stock TB. Justin Starkey at VMP did an intake comparison among the stock '15 compared to the CJ, Boss, '18 Truck, '18 GT and '18GT ported. You can Google the results. I won't spoil it for you, but you already know what intake I use. Lol. Good luck!
 

Users who are viewing this thread



Top