Adding VMP/Roush blower this summer...advice?

Stangra

Active Member
Established Member
Joined
Sep 21, 2018
Messages
272
Location
CA
I would say the only reason to go Roush over VMP is if you are in California and need a CARB sticker to pass smog. Roush has it, VMP does not. I would have gone with a VMP over the Roush if I could have.
↑↑↑ THIS! ↑↑↑
 

tones_RS3

I like members members.
Established Member
Premium Member
Joined
Jan 29, 2016
Messages
21,280
Location
MA
If you use a VMP tune, I'm pretty sure you are going to pass emissions.
VMP tunes are emissions legal, IIRC. They don't turn off the 02 sensors. You may want to confirm, but I'm pretty sure they don't.
 

Stangra

Active Member
Established Member
Joined
Sep 21, 2018
Messages
272
Location
CA
In order to pass smog check in CA any aftermarket part that could effect vehicle emissions must have California Air Resources Board (CARB) Executive Order, like this one for Roush :

Executive Order D-418-23 Roush Industries

And a sticker with this EO number is applied under the hood to certify compliance
 
Last edited:

TType85

Member
Established Member
Joined
Feb 17, 2016
Messages
44
Location
Garden Grove, CA
If you use a VMP tune, I'm pretty sure you are going to pass emissions.
VMP tunes are emissions legal, IIRC. They don't turn off the 02 sensors. You may want to confirm, but I'm pretty sure they don't.

The VMP tune is technically not legal in California. AFAIK the smog check they just check to make sure all the monitors are run/passed. My original VMP Tune did not set all the monitors but the new one so far has everything but the o2/o2 heater set ok but I just checked with the car cold. I will check again tomorrow after my trip to work.

The OP is in Colorado and it looks like they don't do anything for the first 7 years then just check for a check engine light for the next 4. General emissions inspection requirements and information

I got a good deal on my Roush setup at $5800 shipped to my door but I added a VMP tune ($500), bigger injectors ($500) and I still need a CAI ($300+/-).

The Gen2-R kit has a slightly better blower and already has the VMP tune, 56# injectors, a BAP and a CAI for $6300
 

tones_RS3

I like members members.
Established Member
Premium Member
Joined
Jan 29, 2016
Messages
21,280
Location
MA
The VMP tune is technically not legal in California. AFAIK the smog check they just check to make sure all the monitors are run/passed. My original VMP Tune did not set all the monitors but the new one so far has everything but the o2/o2 heater set ok but I just checked with the car
That makes sense.
 

cheeser

Member
Established Member
Joined
Sep 28, 2012
Messages
213
Location
CO
I was thinking about the 2.65, but looks like the 2.3 will work for me as I will not be looking for every last HP....600ish will still put a smile on my face.

I wasn't planning on doing the OPG, but Riddick reminded me about road coursing it where it will be stressed a bit more. I normally only do this once a year...3-4 20 minute sessions on the 2 1/2 mile long course. I put the Koni / Eibach kit on it last year for a slight drop, and Brembos year before that.

For now, here is my parts list:

  • VMP GEN II-R 2.3L TVS Supercharger Kit - Stage 1
  • Ford Performance Aluminum Radiator
  • Ford Performance SVT Performance Cooling Fan
  • Ford Performance 5.0L Coyote Oil Pump Installation Kit
  • Ford Performance High Performance Gerator Oil Pump (or maybe just the MMR OPG and swap) and crankshaft sprocket.
  • McLeod High Performance Hydraulic Clutch Line Upgrade

I will be doing the install myself...looks fairly easy if I take my time...just a lot of steps. One positive in replacing the OPG is that I can modify the front of the timing cover off the car...keep the aluminum from flying everywhere (unless I put plastic everywhere and had a shop vac hose in place).
 
Last edited:

Stangra

Active Member
Established Member
Joined
Sep 21, 2018
Messages
272
Location
CA
I was thinking about the 2.65, but looks like the 2.3 will work for me as I will not be looking for every last HP....600ish will still put a smile on my face.

I wasn't planning on doing the OPG, but Riddick reminded me about road coursing it where it will be stressed a bit more. I normally only do this once a year...3-4 20 minute sessions on the 2 1/2 mile long course. I put the Koni / Eibach kit on it last year for a slight drop, and Brembos year before that.

For now, here is my parts list:

  • VMP GEN II-R 2.3L TVS Supercharger Kit - Stage 1
  • Ford Performance Aluminum Radiator
  • Ford Performance SVT Performance Cooling Fan
  • Ford Performance 5.0L Coyote Oil Pump Installation Kit
  • Ford Performance High Performance Gerator Oil Pump (or maybe just the MMR OPG and swap)
  • McLeod High Performance Hydraulic Clutch Line Upgrade

I will be doing the install myself...looks fairly easy if I take my time...just a lot of steps. One positive in replacing the OPG is that I can modify the front of the timing cover off the car...keep the aluminum from flying everywhere (unless I put plastic everywhere and had a shop vac hose in place).
I found it SOOOOO much easier to modify the timing cover on the bench too! I think the MMR OPGs are a good bet, since I was already there I installed MMR crankshaft timing sprocket too. Even after reading many posts about doing the OPGs I didn't realize just how difficult it was going to be to re-install the lower bolt for the oil pump pickup tube, this might help. I cut a piece of plastic (empty milk bottle) used a cheap paper hole puncher to put a perfect size hole in it and cut a slot to get the bolt into the hole. Bent it about 45* along length for a little rigidity. This inserted between the captive washer & bold head allowed me to align the bolt and feed it into the hole while turning it gently by the threads using needlenose until started. Once started.... WHEEEEW! the rest was easy! Don't forget to put some clean rags underneath in the pan to stop any parts or tools from dropping in!
OPG.jpg

Since you're replacing anyway, this is a lot easier with the radiator out.
 
Last edited:

cheeser

Member
Established Member
Joined
Sep 28, 2012
Messages
213
Location
CO
...I didn't realize just how difficult it was going to be to re-install the lower bolt for the oil pump pickup tube, this might help. I cut a piece of plastic (empty milk bottle) used a cheap paper hole puncher to put a perfect size hole in it and cut a slot to get the bolt into the hole. View attachment 1555347
Since you're replacing anyway, this is a lot easier with the radiator out.

Thanks for the tip.

Reminds me when I replaced oil pan gaskets and timing chain on a 1996 Bronco 351W. The two bolts for reconnecting the oil pump while trying to connect the distributor shaft was a royal pain...was a contortionist. At least these two are accessible with tips like these to help.
 

Riddick

MERICA
Established Member
Joined
Oct 25, 2012
Messages
2,640
Location
Dayton, OH
For now, here is my parts list:

  • VMP GEN II-R 2.3L TVS Supercharger Kit - Stage 1
  • Ford Performance Aluminum Radiator
  • Ford Performance SVT Performance Cooling Fan
  • Ford Performance 5.0L Coyote Oil Pump Installation Kit
  • Ford Performance High Performance Gerator Oil Pump (or maybe just the MMR OPG and swap) and crankshaft sprocket.
  • McLeod High Performance Hydraulic Clutch Line Upgrade

Here a few suggestions I will offer up to save you a little money. I would research the cooling fan for the GT500 rather than buying a Ford Performance one. I would imagine Tasca or Autonation would be considerably cheaper than Ford Performance. Id also consider adding a Reische 170 thermostat since it will all be apart.

Dont waste your money on the oil pump installation kit. Simply reference the OPG install thread above and they list all the gaskets and crank bolt in there, it will be cheaper than buying the install kit. Again, use Tasca or Autonation.... both will take care of you.

As far as OPG goes just do the actual gear and crank sprocket. This will save you a ton of money. You can actually pick up a new OEM oil pump for around 70 bucks and then you can install the gears yourself if your set on a new pump. Its literally a few Torx bolts and you just swap out the old with the new. As far as what brand OPG to go with they will all work. I went with TSS and my buddy has Boundary, both appear top quality and both fit great.

Just like you are talking about I did the OPG/crank sprocket install the same time I did my blower and it made things easier. Took a few days to get it all done but nothing to hard. Since you are pulling the radiator you will have more room for that pick up tube bolt. I did mine by bending over into the engine bay and my back was killing me afterwards.

If you have any questions when you install this please hit me up. We did mine a little over a year ago and I just helped my friend do cams, opg, crank sprocket, blower on his coyote swapped 04 Cobra :). His engine was out of the car and it was so much easier. So much easier that if I ever have to tear into mine again I might drop the motor. If you have access to a lift you could drop the entire front subframe with the motor attached and then lift the car off. Will take a few hour to drop it but the rest of the install will be a breeze.
 

Stangra

Active Member
Established Member
Joined
Sep 21, 2018
Messages
272
Location
CA
...I might drop the motor. If you have access to a lift you could drop the entire front subframe with the motor attached and then lift the car off. Will take a few hour to drop it but the rest of the install will be a breeze.
I almost did this but I knew my "since-I'm-in-there" list woulda become unmanageable :D
 

cheeser

Member
Established Member
Joined
Sep 28, 2012
Messages
213
Location
CO
Here a few suggestions I will offer up to save you a little money. I would research the cooling fan for the GT500 rather than buying a Ford Performance one. I would imagine Tasca or Autonation would be considerably cheaper than Ford Performance. Id also consider adding a Reische 170 thermostat since it will all be apart.

Dont waste your money on the oil pump installation kit. Simply reference the OPG install thread above and they list all the gaskets and crank bolt in there, it will be cheaper than buying the install kit. Again, use Tasca or Autonation.... both will take care of you.

As far as OPG goes just do the actual gear and crank sprocket. This will save you a ton of money. You can actually pick up a new OEM oil pump for around 70 bucks and then you can install the gears yourself if your set on a new pump. Its literally a few Torx bolts and you just swap out the old with the new. As far as what brand OPG to go with they will all work. I went with TSS and my buddy has Boundary, both appear top quality and both fit great.

Just like you are talking about I did the OPG/crank sprocket install the same time I did my blower and it made things easier. Took a few days to get it all done but nothing to hard. Since you are pulling the radiator you will have more room for that pick up tube bolt. I did mine by bending over into the engine bay and my back was killing me afterwards.

If you have any questions when you install this please hit me up. We did mine a little over a year ago and I just helped my friend do cams, opg, crank sprocket, blower on his coyote swapped 04 Cobra :). His engine was out of the car and it was so much easier. So much easier that if I ever have to tear into mine again I might drop the motor. If you have access to a lift you could drop the entire front subframe with the motor attached and then lift the car off. Will take a few hour to drop it but the rest of the install will be a breeze.

Thanks...

For the fan, I believe the one I referenced is the same one used in the GT500. I will double check with Tasca or others as suggested though along with all of the bit pieces (gaskets and such).

I was thinking about just the gears vs the whole kit. As noted, just a matter of pulling it apart. I might just go ahead and buy a new pump then and make the swap ahead of time.

My only other question is if I might as well replace the seal on the timing cover since it is off....car only has 35k on it so it may not be needed. Just one of those things if it is pulled apart to change these cheap pieces.
 

Riddick

MERICA
Established Member
Joined
Oct 25, 2012
Messages
2,640
Location
Dayton, OH
I'd change out the timing cover seal, I replaced mine and the engine only had 8k on it. Just makes sense since it's all apart. I bought all new seals and it came out to roughly 30 bucks if I remember correctly. If you follow that tutorial and buy all recommended parts you really can't go wrong. Only other suggestion I would make is I would purchase the crank pulley install tool, will make it easy.

Sent from my Moto Z (2) using Tapatalk
 

decipha

Well-Known Member
Established Member
Joined
Jul 12, 2008
Messages
1,019
Location
New Orleans, LA
for road course i would highly recommend you put meth injection on it. Get yourself a 5 gallon tank and mount it in the trunk. The cooling effects will outweigh the additional weight.
 

cheeser

Member
Established Member
Joined
Sep 28, 2012
Messages
213
Location
CO
You really can't beat the Boss 302/Track Pack Radiator and 13-14 GT 500 Cooling fan combo for the money.

That was my thought as well.

I did modify my list of things to purchase...going to buy an extra timing cover and oil pump housing and modify them ahead of time. Yes, it is a few extra bucks, but it will allow me to complete things ahead of time to try and reduce my overall down time for when I start pulling it apart next month.
 

Riddick

MERICA
Established Member
Joined
Oct 25, 2012
Messages
2,640
Location
Dayton, OH
That was my thought as well.

I did modify my list of things to purchase...going to buy an extra timing cover and oil pump housing and modify them ahead of time. Yes, it is a few extra bucks, but it will allow me to complete things ahead of time to try and reduce my overall down time for when I start pulling it apart next month.
https://www.cjponyparts.com/ford-pe...MI9df9kMHn4QIVUP_jBx3RGQ0PEAQYAyABEgJqS_D_BwE

Ford Racing makes a cover you can swap on directly.

Sent from my Moto Z (2) using Tapatalk
 

OX1

Well-Known Member
Established Member
Joined
Sep 23, 2015
Messages
833
Location
New Jersey
I believe VMP's stage 1 kits are emissions compliant. I think the difference is in the CAI provided.

Hard to claim it is CARB approved with VMP embossed in the blower though.
That's the main reason I went with Roush, just in case.

Living in a POS liberal state, you never know. If we fail emissions at
state inspection for any reason, you have to go to private garage and
get it "fixed" (not allowed to fix and re-test).
 

TType85

Member
Established Member
Joined
Feb 17, 2016
Messages
44
Location
Garden Grove, CA
Hard to claim it is CARB approved with VMP embossed in the blower though.
That's the main reason I went with Roush, just in case.

Living in a POS liberal state, you never know. If we fail emissions at
state inspection for any reason, you have to go to private garage and
get it "fixed" (not allowed to fix and re-test).

100% why I went Roush over the VMP. I am tempted to go with a gen 3 and make a plate that has the Roush logo on it to go over the VMP logo :p
 

Users who are viewing this thread



Top