Fellow SVTP guys - I need your help.

[Liv4Spd]

A few weeks ago I was driving down HW1, down the coast of CA and had face full of debris shoot out from under a semi's rear tires and decimate my front bumper.

After getting over the initial shock I came to the realization that I was going to have to replace the bumper cover as well some of the underlying pieces. This being the case, for the past few weeks I’ve been in search of some NOS/OEM replacement parts, but to no availe.

So, I'm resorting to my final option, the forum community for help.

If anyone has/knows of any leads on the following parts I would be very grateful.

Parts / Numbers are as follows:
Bumper Cover - F3PZ8190A
Face Bar – E7ZZ17757A
P/S Cooler – F0ZZ3D746A

Thanks in advance
Rahmi

 

[suaveflooder]

Why not go to a junkyard? When I had my fox it was the only place I could get a lot of the parts I needed.

 

[93_SVT_FREAK]

If I were in your shoes I'd contact this guy about the front bumper and see if he still has it.

Auction is over.... (Not my stuff)

http://cgi.ebay.com/ebaymotors/ws/e...40&_trksid=m38&_nkw=330255166365&_nd1=&_fvi=1

 

[jspalmer01]

Another option would be to contact Jim Dingell at Performance Parts Incorporated, or PPI (located in Virginia and on the web). He specializes in late model Mustang Cobra parts, especially 1993. Jim may have something on hand or be able to source it for you. Good luck.

 

[Liv4Spd]

Thanks for following up guys; I'll look into your sources. If anyone else has any leads please don’t be shy to PM me or post on this thread. Your help is much appreciated!

 

[DAVESVT2000]

FYI Cervinis has probably the best quality reproduction bumper out there if you end up having to go that route......

 

[tunedin302]

Another option would be to contact Jim Dingell at Performance Parts Incorporated, or PPI (located in Virginia and on the web). He specializes in late model Mustang Cobra parts, especially 1993. Jim may have something on hand or be able to source it for you. Good luck.

+1 - lots of dealings with Jim and very pleased.

 

[Liv4Spd]

FYI Cervinis has probably the best quality reproduction bumper out there if you end up having to go that route......

Noted - Thanks

 

[cobra186]

The "face bar" .i.e fiberglass bumper is the same as any 87-93 LX, GT or Cobra

The P.S. Cooler is the same as any 90-93 5.0 LX, GT or Cobra

The original cobra bumper cover is specific to the 93 Cobra when originally built, but all "service parts/OEM replacement" are the same as any 87-93 GT with the center cut out for the cobra grille insert.

 

[1BAD93SVT]

there's a place in LA named CI performance that parts out cobra's every now and then. 818 are code. usually on recycler.com

 

[Liv4Spd]

Thanks again fellas!

 

[bat-stang]

The "face bar" .i.e fiberglass bumper is the same as any 87-93 LX, GT or Cobra

The P.S. Cooler is the same as any 90-93 5.0 LX, GT or Cobra

The original cobra bumper cover is specific to the 93 Cobra when originally built, but all "service parts/OEM replacement" are the same as any 87-93 GT with the center cut out for the cobra grille insert.

+1 ( I know you didn't ask but) If you need the Cobra insert I found the front part:

(Comes with the Horsey)
Found it here:
http://www.foxmustangrestoration.com/?p=vp&id=55

 

[bat-stang]

Oops...