Recent content by CrazyPerson

2000 mustang gt 4.6 took off old cams went to put on new cams ligned up copper marks to crankshaft sprocket marks crankshaft at 12 oclock when i barely move it left to right it wants to touch the valves.... so i put stock cams back on and same thing. car drove fine before hand....the...

So i just put the engine back together and when i turn it over im not getting any oil pressure at all. I turned it over for about 30 seconds and even the oil filter didnt get any oil into it....any ideas? i dont want to keep turning it over for a long time and lose all the oil at the bearings...

the dyno numbers are way better than i intended, i was hoping to get around 600RWHP and put out a lot more then that! 661.8 RWHP 724.5 RWTQ the motor consists of a 351 clevland stroked to 385 385 JE stroker forged pisons scat forged hbeam rods scat forged balanced crank 4v cast...

MORE PICS ADDED! we'll i know this is the wrong spot but i just finished the 67 mustang and the dyno numbers im very happy with. 661.8 RWHP 724.5 RWTQ the motor consists of a 351 clevland stroked to 385 385 JE stroker forged pisons scat forged hbeam rods scat forged balanced crank 4v cast...

we'll i know this is the wrong spot but i just finished the 67 mustang and the dyno numbers im very happy with. 661.8 RWHP 724.5 RWTQ the motor consists of a 351 clevland stroked to 385 385 JE stroker forged pisons scat forged hbeam rods scat forged balanced crank 4v cast heads...

anyone have any links for a nice budget navigator build? i just came across a free navi motor with a spun rod bearing. i'll have to replace the crank since it ruined the crank. i was wondering if anyone knows of a good thread or what not for a good budget navi NA build that puts over 400HP

i just bought a 97 cobra with a kennebell supercharger for $2500 with a blown headgasket. i was able to drop the oil pan before buying, the internals are fine. i've always delt with NA motors, i know nothing about superchargers. what does a kenne bell boost a pump do? it also has ethanol...

i just bought a 97 cobra with a blown headgasket with a kenne bell supercharger for $2500 i dropped the oil pan before buying it and all the internals looked fine. i just dont know anything about super chargers as i've always built NA motors. what is a kenne bell boost a pump? is there...

so far i've got the dash frame in and welded. that took 10 hours to get it all to line up right and i have to cut and trim the dash down. also have half the wiring done under the dash now. i bought wrecked 97 cobra and im converting everything to the 88coupe...

im converting a sn95 cobra that i bought wrecked and putting everything into a coupe. just finished customizing the dash in place. here is a few pics. [img=http://img197.imageshack.us/img197/3659/0715091513a.th.jpg] [img=http://img365.imageshack.us/img365/8638/07150915132.th.jpg]

i need all these current items. I NEED FULL SN95 WIRING HARNESS minus the engine harness and computer. hydroboost brake setup with all lines 255 fuel pump

anyone know what i would need to put my 98 cobra engine in a 93 coupe?

so i just did a motor swap on a 90 mustang 5.0. i've done about 8-10 motor swaps and have never had this problem. for some reason the injectors wont squirt when engine is being cranked over. any ideas? i've checked everything including the ground on the bellhousing. all of it >< im stumped. the...

what would be a good kmember to get at a reasonable price? and A arms that can use stock springs..

my buddy is going to put the ford gt cams in his 03 mach1. he said i could put them in my car also. do they give an increase on N/A motor?