Recent content by dover

Who's using them, and who did you have do them? Debating on making the switch. It only makes sense to go that route and free up the flow a bit. You all notice any power increase? Any torque decrease? Thank you guys. Side note I just noticed I have been a member for 4 years wow time flys by.

I have a SRA out of an 01 Bullit that has quite a few things done. I am looking to go back to a nice IRS with low miles. Edit: 19k miles on the car, 1500 on the whole SRA -Moser 33 Spline Axles -Moser Spool -C-Clip Elim. -Welded Tubes -UPR UCA -UPR LCA -UPR Spherical Bushings -UPR...

I just currently got stationed at Fort Eustis, for the time being. Not sure as to how long I will be here but, what I need to know is: What good shops to work on my 03 Cobra are in the area? Who is the best tuner in the area? Is there a community forum for the Tidewater/Newport...

Does anyone sell aftermarket stiffer mounts? Does anyone have some in their car already? If so what kind of power are you making and how does it feel? More vibration? I think it would greatly improve shifts right? Thanks! :rockon:

I have had my car for sale for little while it appears it isn't going anywhere. So I am debating on throwing an auto in the car and some 3.27's or maybe lower in the rear. I already have a .020 over motor and built 8.8. Now I already have a T76BB kit on the car makes 660 @ 18lbs (low timing...

I have 15x10 and 15x4 TRUE Weld Prostars. Tires: Hoosier Quick Time Pro's: 27x11.5x15 Hoosier Fronts: 160/55/15's (I believe I can't remember exactly) I would like to trade for a nice street wheel/tire. I don't have anything to put on the car so no I won't sell out right. I also have...

Off a 2003. XCAL3 $257 TYD. BA3000 $206 TYD. Everything will be shipped via UPS with insurance.

Please add 3% if using Paypal. XCAL3 - $325

FS/FT 2003 Hellion Cobra with only 19k miles, over $30k invested I am the third owner, I bought the car with 12,xxx back in 2006. The Hellion T-76BB Kit went on at 15,xxx miles. Car on stock motor with 18lbs made 717.7/672. The car is very capable of 1,xxx with more boost and the addition of...

I need this to happen ASAP my car has been down way to long and this is a last minute change to the build. My T-56 details: 18K miles BRAND NEW Southbend Stage 5 clutch Stock flywheel BRAND NEW Liberty 26 Spline Input BRAND NEW Lethal Perf. Aluminum TOB Sleeve BRAND NEW HD TOB BRAND NEW New...

This isn't getting much attention in the Turbo Cobra Section so I am opening it up a bit. What RPM are you leaving from? Are you using a two step? How much boost are you building at the line? Are you spraying? Also the car is a Hellion T76 car. My setup: 01 Bullit 8.8 Moser...

What RPM are you leaving from? Are you using a two step? How much boost are you building at the line? Are you spraying? Also the car is a Hellion T76 car. My setup: 01 Bullit 8.8 Moser 33 Spline Axles Moser Spool C-Clip Elim. Welded tubes UPR Chrome Moly Adj. Race Lowers UPR Chrome Moly...

60's off my 03 Cobra, had them in for about 2k miles, have to up some 80's! $275 obo shipped.

60's off my 03 Cobra, had them in for about 2k miles, have to up some 80's! $300 obo shipped.

Maybe this has been addressed already and I am just unable to locate the thread but: I have an 8.8 (still has the cobra brakes on the back) in my 03 and want to do slicks an skinnies. If I'm not mistaken its 15x4 w/ .5" spacer and 1.75in BS, and 15x10 w/ 6.5in BS. If I got with a smaller BS...