Recent content by HrsePwr

Yes I will eventually do the boss / cobra ported setup but for now I want to do the stock 5.0 manifold / tb. Does anyone have the link to Shaun AED’s manifold work ? I don’t want to do too much to it and loose power.

I’m the same as the OP. The 11-12 front ends look a lot better then the 13-14’s ( with the 13-14 headlights in ). & The rear tails on the 13-14’s look awesome. I plan on switching to the 13-14 but in my area they cost so damn much. :( Anyways to the OP ; do it ! Will look nice !!!

hi I apologize but I searched and did not find the thread. I believe Shaun from AED gained 8whp across , by porting the stock Coyote intake manifold ? I bought a stock tb and intake manifold. I have a guy that will bore the stock tb to 85mm. Now I’m looking at what to do to the stock...

Ok thanks to the couple of you that gave honest/positive answers. If you have nothing positive to say keep your 0.02 to your self !!! Thanks !!! I was thinking of adding a set of long tubes but the cost of headers and the install is just nuts. Unless I can find someone locally who will...

Hey guys, I’m trying to make my Mustang the loudest it can be. Last year I had : Jba off road H-pipe , no resonators , pypes Bomb Axel Back Muffler deletes ( tips were resonated about 10” ) This Year : Pypes off road X-pipe , no resonators, MBRP axel back muffler deletes. ( this setup I...

Update : Car has gone 12.5 @ 115mph with a 1.9 60' 18x10 Shelby Rims with 285/40/18 Nitto Nt05r tires. Setup : Airraid Cai Jba offroad h Bmr drag springs - koni Yellows Steeda uca Bmr pan hard bar & brace Bmr lower control arms Alum D/S Pypes Muffler deletes Bmr front sway bar delete...

http://www.jegs.com/i/Mickey-Thompson/672/3054ST/10002/-1 Would those slicks be good ? What should i launch them at ?

So which 28" bias ply do you suggest ? And I will also be running skinnies in the front.

Im not looking for " too much gear , you dont want 4.10's " etc. Im looking for people who ACTUALLY have 4.10 gears , there set-up and there 1/4 mile times. Thanks,

Ok so my best time at the track was on my Nitto Nt05r tires. I had 18x10 rims, and 285/40/18 Nittos. I hit a best of 12.49 @ 112 mph with a 1.9 60' ft. Yet on a michellin 19" tire 265/40/19 i ran a 12.79 @ 117 mph with a 2.1 60' . So clearly the car can do a 11.9 1/4 mile as is if I can...

I already bought the 4.10 gears and install kit. Car makes : 410whp/394wtq. Cai, off road h-pipe , axel back exhaust , tune. Suspension : bmr front sway bar delete, bmr drag springs , koni yellow adj.shocks, adj. rear upper arm, lower control arms and brackets, panhard bar and brace...

Does anyone have any 1/4 mile times with a 2011+ mustang Gt with 4.10 gears and other mods ? Im planning to go 4.10's , my mustang is 80% street driven and 20% track. Im aiming for 11's n/a, 4.10's , bolt-ons, slicks and a tune. What size tires / rims etc would I need ? Best time so far is...

Ok guys here was my set-up when I ran 12.7 @115mph Car is a : 2011 Mustang GT Convertible. Manual with 3.55gears : 2011 Mustang GT 6-Sp's Manual 3.55 gears. - AirRaid Cai - Jba Off-road H-pipe -Pypes Axel back - Bama 93 v2R Tune - Steeda Adj. UCA - Whiteline LCA's Tires were : 265/40/19...

Hi guys, 2011 Mustang GT Convertible. 6-Spd manual. 3.55gears Mods : AirRaid Cai Bama 93R v2 Tune Jba Off-Road H-pipe Pypes Axel Back Bmr Front rad support/sway bar delete Bmr Rear Drag springs Koni Adj. RearShocks Steeda Adj. Uca WhiteLine Lower Control Arms WhiteLine Lower Control Arm...

Hi, So I brought my 2011 5.0L conv. To the track stock. And it had VERY BAD wheel hop. I had to take off at idle. It ran 13.4@108mph. All traction controls off. I could not even take off at anything above idle or there would be VERY BAD wheel hop. So I bought some brand new : Steeda...