Recent content by ZD302GT

  1. ZD302GT

    SAI manifold fitting

    When doing research to find some caps or have some made I had found that the thread was 1/2" flare. I never got past that and ended up using the welded up tubes i had.
  2. ZD302GT

    Bilstein B8

    The solid axle and IRS rear shocks are different.
  3. ZD302GT

    Any 98 guys still running aviator pump?

    I used a lethal 340lph on my 98 and its been in there over 10 years now. I had to do some clearancing with a dremel to get it to work but it wasnt too terrible.
  4. ZD302GT

    96 Cobra Teksid build

    The stock piston has a 3cc dish so if you can find something similar to that you will have close to the stock compression ratio.
  5. ZD302GT

    Let's talk clutches

    If you get something from McLeod, make sure you take it to be balanced before you install it. It is a shame they don't do this beforehand, especially since the 4.6 is an internally balanced architecture. Interesting, I replaced my fork with a new ford unit as well when doing the clutch. I paid...
  6. ZD302GT

    Let's talk clutches

    I just put in a McLeod Street Pro (11") with their billet flywheel in my 2001 cobra and I am very disappointed with it. The engagement is all the way at the top of the pedal which makes it unpleasant to drive this is even after speaking with them about adjustments and they had me go to a...
  7. ZD302GT

    Exhaust manifold stud size? Where to buy ( discontinued from Ford ).

    Get a cheapy thread gauge so you can determind the pitch and then you can use dial calipers to determine the diameter and length of the stud.
  8. ZD302GT

    WANTED: BBK Off Road X-Pipe for Longtubes & Stingers for SRA

    Also, don’t give any money to LAR Performance. I tried buying an X pipe from them and it is not close to fitting and they have no interest in making it right or giving me a refund. The cobra t45s have a different tail shaft mount that moves the crossmember back compared to the GT t45. So I...
  9. ZD302GT

    4.6 4v Teardown & Build Thread

    Thanks for making a build thread. I enjoy seeing 4.6 builds.
  10. ZD302GT

    Rebuilding my 98 cobra 4v, need help please

    How is your build going?
  11. ZD302GT

    WANTED: BBK Off Road X-Pipe for Longtubes & Stingers for SRA

    Still looking for a BBK X-Pipe
  12. ZD302GT

    Rear control arm help

    Probably easier and faster to buy some UPR or maximum motorsports units. And you lose some weight with those as well.
  13. ZD302GT

    96dreamer's Never Ending Build Thread

    The thinnest spacer that they provided that goes between the alternator bearing and pulley was too still too thick and did not allow full thread engagement of the nut on the front side of the pulley. I suppose it didn't provide enough clamp force to hold it still. I guess it started spinning on...
  14. ZD302GT

    96dreamer's Never Ending Build Thread

    Interior looks great! How did you attach the phone mount to the dash? Drill some holes and bolt it in back behind the radio bezel? My car just ate a March alternator pulley a month ago. It wallowed out the center hole. It was a horrible design, do not recommend. So I had to go back to the stock...
  15. ZD302GT

    96dreamer's Never Ending Build Thread

    That's a bummer about the pump, in my old age I tend to only buy mechanical parts that are motorcraft. Way too much junk out there to buy anything else. I am always tempted by lightweight though. Hope it has long longevity for you! I just recently purchased a new battery and im hoping the next...

Top