Hey guys,
I took my car out last Saturday and had a few runs. Driving home I noticed heavy clunking sounds when making turns from the rear end of the car. Anyone have this issue and what was the repair? Thanks!
Hello,
We are trying to install a fly by wire setup for nitrous. Does anyone know which wire is the 0-5v pin or wire on the tps? A pin diagram would be great too. Thanks
Which line goes to the top and bottom of
the intercooler? I’m assuming the cool water which comes from the bottom of the heat exchanger goes to the top port of the intercooler?
Sent from my iPhone using Tapatalk
This is kit is from THP(turbohorsepower.com) this is the t3/t4 hot side, 38mm Tial wastegates, downpipes, h-pipe and bassani cat back. O2 extensions with vband clamps included. You can get them ceramic coated and they will be good as new. 2000 obo
Sent from my iPhone using Tapatalk
BPS Crankcase Exhaust Evacuation System U002
Has anyone used this setup instead of using a vented catch can? I was wondering what the pros and cons of using this setup
Sent from my iPhone using Tapatalk
Hey guys I just received my motor from MPR. Specifically states on the paper work to prime the motor before starting it and using the starter will not work. I would like to hear how you guys did this.
Sent from my iPhone using Tapatalk
My goal is to make about 1200 rwhp and I have the bottom end built. Now I don't have the heads on there yet because I heard with the stock heads that kind of power can't be reached. My plan is to go bigger blower of course. Can 1200 be done with a bigger blower with stock heads?
Sent from my...
Helping a friend remove his kenne bell. He has the 2.8 mammoth non lc. Does the elbow need to come off? Seems like all the bolts we can get to have been removed but under the elbow there are a few bolts. Thanks for any help
Just noticed today that one of the pulleys in my car is being noisy. Sounds as if it's coming from the blower. I have upper and lower pulley with a ported blower. Has anyone had an issue with their pulley or blower? The speed of the noise gets faster as rpms go up. I have a little over 7k...
I've had bad luck with my twin turbo build. I had rod knock happen twice and going on my 3rd rebuild. It's been horrible. I'm just curious how everyones build experience has been? And how long it's been running now and how much boost and hp is everyone putting down?
Few runs in Mexico. In the first link the first 3 or 4 races are between a mazda 3 and gto both boltons then we run. The 2nd link are a rear view from the zo6 then he changes it to a side view.
Gt500 vs z06 454 200shot vs supra 2jz single turbo: http://youtu.be/kZSspu3KiDI...
Where can I find a relay switch for the heat exchanger pump so that i can run the pump while the engine is off? I know on the terminators you could but can't find anything on these shelbys.
I hear kind of a knock as my motor starts to get up to 3k rpms. But if I just rev it then I don't hear it. I'm taking it to the dealership tomorrow to get checked. Maybe these motors have some valve train noise? This motor has about 1,000 miles and I don't drive it hard.
So on the sticker for my 14 Shelby it shows i paid for the cover. It just wasn't in the car. So i called the dealer and they said give us a week. Picked it up and it looks like a plain mustang cover. Does not have any Shelby decals. Can someone post a pic so i can show these guys what it looks...
http://news.3m.com/press-release/company/new-3m-paint-defender-system-offers-invisible-paint-protection-easy-use-spray
I know my terminator gets rock chips. I was thinking about using this stuff on my gt500 before it gets any chips.