Search results

  1. Bulldogger

    Fabricators

    Need a fabricator or machine shop who can make me some 6061 pulley sets. Looking for a place out on Long Island or vicinity. Thanks Dave
  2. Bulldogger

    Stock GT500 parts

    I have a stock parts off my GT500. TB has no electrics. $60 includes shipping. Lower control arms $65 shipped Upper control arm $65 shipped Stock Driveshaft $150 shipped Panbar $45 shipped Stock H-pipe with cats 125 plus shipping. Stock blower $600. Blower has 250 miles on it. All other...
  3. Bulldogger

    Fays2 Watts link

    Well, finally got around to installing it. Car prior on the street was pretty crappy as far as handling went. Acceleration around a corner with any type of dip or pothole on the road almost brought the ass around. Well not anymore. Plus at higher speeds say 120+ the car has great manners where...
  4. Bulldogger

    Drivers seat

    Anybody know how to pull the black plastic bottom trim off where the controls are? My mustang had a squeek and everyone thought either the exhaust or LCA's. Anyway I guess my fat ass is moving the plastic on the seat on bumps and it sounds like a f'n bird.
  5. Bulldogger

    Big Thanks to ILLTAKETWILIGHT

    BIG THANKS to I'll take twilight who was nice enough to read my want to buy request in the market place. Well now I have a VMP 72mm throttle body and my car should be all set for the Real speed Dyno day. Car has been running fine but I just had the feeling the stock throttle body was choking...
  6. Bulldogger

    VMP throttle body

    Anybody have one for sale looking for the 67MM or 72mm Thanks. Yes I posted over in for sale section a WTB but just in case anyone knows of one.
  7. Bulldogger

    Competition Engineering

    These guys make a real strong bolt in saftey loop. No need to drop the drive shaft either. If your running a one piece aluminum driveshaft like me, the part number is C3163 for the loop
  8. Bulldogger

    Wtb vmp tb

    I'm looking for a VMP Throttle body either 67mm or 72mm Thanks. Dave
  9. Bulldogger

    New AFCO Harness Install

    Basically the new harness install uses a different location for install of the new dual relay and fuse holder positions. After removing the front bumper and removing the old harness, you will begin to install the new harness. The dual relay will now be located underneath the passanger side...
  10. Bulldogger

    Shaftmasters

    Just figured I'd mention these guys for Aluminum driveshafts if anyone is interested. I bought one and it was really nice to see that when it arrived it came with a socket for the 6 new bolts they supplied. It also came with blue thread locker and a reamer to run through the threads to remove...
  11. Bulldogger

    LCA Bolts

    For the guys that changed out the LCA arms did you also buy new bolts or re-use the factory ones. J&M states to use new hardware just curious.
  12. Bulldogger

    EV monitor

    Had the battery disconnected for awhile while I welded in the BMR frame connectors. Car is up and running fine, but the EV monitor is still flashing not ready all other systems are ready. I have put 250 miles on the car but the EVAP won't set. Any ideas? no codes just not setting. Can't pass...
  13. Bulldogger

    Firewire to SCT

    I have the 6 pin fire wire that allows you to see and log A/F ratios with the SCT Tuner. Anyone know how the firewire cables get soldered into the Dynojet wideband or acquistion cable.
  14. Bulldogger

    TVS & Dynatech LT's

    Finally put back together and up and running. Had a slight delay with the powder coating of the coil pack covers but it's done :banana::banana:
  15. Bulldogger

    Finally

    The VMP has arrived and I can finally install it and get the pig up and running:pepper:
  16. Bulldogger

    Panhard Bar

    Anyway to minimize the twist to the right on hard launches? Do new lower arms or anything else really minimize it other then something like Watts Linkage?? Thanks
  17. Bulldogger

    Dynatech Hiflo Cats

    After 2007 ford did away with the tranny mount exhaust hangers. What did you guys do with the cat mounting rods. Did you leave them and make up you own mounts, or just cut them off. The exhaust is a pretty far run for just tail pipe supports and nothing else.
  18. Bulldogger

    Dynatech LT's

    For the guys who already installed them, did you need to take out the alternator for the front bottom bolt on the driver's side or were you able to get it with a flexable combinations of sockets and extensions Thanks
  19. Bulldogger

    Shifter knob

    Solid white shift knob with 12mm x 1.75 thread $15.00 shipped
  20. Bulldogger

    Grade 8 Bolts

    Going to install my Dynatechs soon and was wondering if the Grade 8 locking bolts bare worth while or just stick with the included header bolts. Thanks
  21. Bulldogger

    TVS Blower

    I know that this is a roots style blower and according to everything I've read is no where near as efficient as a twin screw. My question is then why do people use it?? VMP uses it on his car and make over 700hp. It must have some type of advantage over a twin screw. Being a twin always...
  22. Bulldogger

    Factory mufflers

    I have a set of factory axle back mufflers. They are new as original owner had bassani's put on prior to purchase.
  23. Bulldogger

    Shifter Knob

    I just bought my GT500 and it had a solid white shifter knob. Thread is 12mm x 1.75 it fits the steeda triax if anyone is interested. I don't like it and replaced it with the black one. Updated with a picture of the shiney white ball $15.00 includes shipping.
  24. Bulldogger

    5w-50 oils

    From other members we see that Motorcraft 5w-50 oil is crap, so lets see if we can find some other quality oils. We have some choices Redline Castrol Mobil 1 Schaffers Pennzoil Valvoline Does anybody have any UOA's on these brands as these are all 5w-50. I think everyone would...
  25. Bulldogger

    Officially One Of The Gang

    Drove to Michigan and back to pick up the new ride. 2008 Red GT500. Dealer installed items for the original owner were Steeda Triax Shifter and Bassani Axel back exhaust. Car has a whopping 248 miles on the clock with over a year and a half on the 3yr/36 bumper to bumper warranty. Car has...

Top