Search results

Anybody seen this new show on Discovery? I've seen the first couple of episodes. If you're not familiar with it, basically its a reality show that follows 2 perspectives in rural Virginia. One story line is a law enforcement officer trying to bust people trafficking and making moonshine. The...

This is the last one they had for sale. I never installed it, and probably never will as I've decided to go a different direction with the car and won't be needing it. I'm not in rush to sell it, so I want to get out of it what I have in it. I doubt there are any other new ones sitting...

$300, you pay shipping Bought this off rodfarva, never installed it in my car. Probably gonna skip this and go straight to an upgraded fuel system.

How many miles before the first mod? Mine had 4.10's waiting on it at the dealership before it ever got there, lol. Went for a ~50 mile test drive before they were installed. So, about 50 miles here. I suspect most of these numbers will be pretty low

It seems like I'm always living in rodfarva's shadow, but I posted a new pb for me today as well. I know the RT sucked, but wasn't really focusing on the lights. All my power adding mods are listed in my sig. The car still has quite a bit left in it as is. I'm still on factory shocks and...

Anybody know where the tach signal wire is on the ecu plugs? I'm installing a new tach that says to tie into the signal wire, but doesn't give it's location.

Car's currently on a diet. Going to remove the front seats and replace with a race seat sometime in the near future. I've seen rodfarva's Corbeau in person, which is a very nice piece (and probably what I will ultimately go with). However, I was wondering what other options there are out there...

Just brainstorming here. I understand that it is an issue trying to fit larger than 72lb injectors with a Whipple 2.9. Just wondering if that is the case for a TVS as well? I assume that it is not an issue for the larger Whipple blowers.

Just wondered if there are any companies that will "beef up" the TR6060. Most of my internet searches just produced companies that sell it as an upgrade to other transmissions, but none that actually built it up to handle more power. I don't have any issues currently, and don't expect to...

So where does everyone have their shift light mounted? The A-pillar seems like an obvious place to me, just wondered what others had done. Pics would be great. I was planning on mounting a 5" cobra jet tach with shift light, but I don't want to drill holes in my dash. Plus, it looks like...

Best I remember they switched over to E-85 and were making over 1000rwhp after replacing a broken valve keeper. Just wondering if they've made any more runs with the new setup or have any updates? I can't find anything on the web.

I'm currently running the KR shifter linkage which is much better than stock and fine for the street, but it still leaves a lot to be desired at the track. Any thoughts on these 3 units?

I know the limiting factor in the stock engine seems to be the rods. I was just wondering with a built short block what rpm are the heads (namely, the valve springs) good for?

Finally got the car back from my tuner and had a chance to take it to the track for the first time. I'm very pleased with everything. The roll bar and tuning was done by Greg Mayton at Speedy Dyno in Owensboro, KY. He also was able to order the wheels for an excellent price. If there is...

Just wondering if anybody that's done a built engine on here went with a higher compression than stock. I know that the higher comp ratio limits how much boost you can run on pump gas. Just curious if anyone has done it. I think the flat tops available with MMR builds increases it to 9.5:1...

Thinking about upgrading to a 9 inch rear end sometime before I do a built motor next winter. After weighing the options, I think I'll be more satisfied with this in the long run rather than upgrading the 8.8 and adding c-clip eliminators. I know Moser, Currie, and Strange are big names in the...

What's the tallest rear slick you can run without clearance issues? I see a lot of guys running 28"x10.5". However, the Cobra Jets run 29"x10.5" and 30"x10.5". I just wondered if anyone has run a 29" or 30" on a GT500. I've got a set of 15" Bogart wheels ordered. Right now I have the stock...

Anybody running a GT500 in NHRA events? If so what class? From what I can tell, it appears a coupe doesn't qualify for any of the Stock classes, but it does fall into Super Stock B (which looks to be extremely competitive in the low 9's). I'm pretty new to the drag race scene and just trying...