Search results

SOLD SOLD SOLD Sent from my SM-N920V using Tapatalk

Sadly it's time to move on to something new. I bought the truck a little 3 years ago from another member. I'll get chassis has 169,xxx and the motor has been replaced in 2011. I cannot verify the milage on the motor. Right now it runs but does not drive. There is an issue with the transmission...

Used Roush TVS bare case. Case is in good shape from what I can see. This is a bare case only. No bearings, elbow, bypass, snout, mid plate or rotors. Asking $400 plus the ride.

Roush TVS bare case. Used but looks to be fine. This is a case only. No internals, no snout, no bypass just the case. $400 shipped in the lower 48

2002 DSG HD #7706 167,135mi on chassis roughly 15k on motor. Ford spec rebuild in 2011. Blower was rebuilt last month. Lightning upper pulley and snout. MP idler bridge with two 100mm idlers and one 90mm idler. C&L cold air intake and MAF with K&N filter. Accufab single blade throttle...

I know this is t "GT500" stuff but its close. Just finished this 112MP for a customer. Ported by Brett Lemenager and polished by myself (3rd Row Innovations). Also polished the plenum but that's going on my truck.

I know this is t "Gt500" stuff but its close. Just finished this 112MP for a customer. Ported by Brett Lemenager and polished by myself (3rd Row Innovations). Also polished the plenum but that's going on my truck.

Just finished this 112MP for a customer. Ported by Brett Lemenager and polished by myself (3rd Row Innovations). Also polished the plenum but that's going on my truck.

Just finished this 112MP for a customer. Ported by Brett Lemenager and polished by myself (3rd Row Innovations). Also polished the plenum but that's going on my truck.

I know this is t "Cobra" stuff but its close. Just finished this 112MP for a customer. Ported by Brett Lemenager and polished by myself (3rd Row Innovations). Also polished the plenum but that's going on my truck.

Need a polished tvs asap 214 771 1974

Does anyone in the DFW area have a puller to remove the pulley from the snout? I need one asap. Any help will be appreciated. Thanks

Have a dual over head console pod. Replaces the factory compass and retains all of the map lighting and sunroof controls. $225 shipped

Got a few shop tools I don't use anymore.......all are OBO located in DFW Acra 12spd Drill Press.....$650 obo IT HAS BEEN IN STORAGE AND WAS NEVER USED. IT HAS SOME SCUFFS AND DINGS FROM MOVING. ALSO HAS SURFACE RUST ON THE WORKING PLATE AND THE COLUMN. EVERYTHING MOVES FREELY. Utility...

A couple of gauge pods I have on the bench. I can add pedal or slider buttons. $150 each lmk

What's a run of the mill 5.4 Block crank and rods worth ? 2011 5.4

Black JLP CAI with 90mm MAF and filter. $150 shipped $125 w/o MAF

Black JLP CAI with 90mm MAF and filter. $150 shipped $125 w/o MAF

Nvm....

Stock 90mm maf. Not much to say about a MAF. Works as it should. $50 shipped 2# Ring....SOLD BBK Twin 65mm TB.....SOLD Stock TB......SOLD OW Handle w/Keypad 6 pin....SOLD HD Bedrug......$175 Local Pick up only Add PP Fees or send as a gift

Stock 90mm maf. Not much to say about a MAF. Works as it should. $50 shipped 2# Ring....$60 Shipped Stock HD Air Box and Boot.....$75 Shipped Stock L Air Box and boot.....$75 Shipped BBK Twin 65mm TB.....$175 Shipped Stock TB......$45 shipped OW Handle w/Keypad 6 pin....$50 Shipped HD...

Anyone have any junk 2-1/16 gauges? I don't need anything that works. These are for mock up purposes only. I appreciate it.

I have a door that will fit any mustang 94-98. It's in fair condition but has all the function parts. Included with the door is the exterior handle, interior handle, glass, window motor, lock actuator, and latch assembley, there may be more little parts in there I'm forgetting... Txt or email me...