Search results

Does anyone know how to get in touch with Steve from Tru Forged? I need to source one of his radiater caps that goes on his combo overflow tanks. Thank you in advance.

Does anyone know how to get in touch with Steve from Tru Forged? I picked up one of his combo radiator/blower overflow tanks and am looking for one of his radiator overflow caps. Thank you in advance.

Does anyone know if True Forged is still in business? I have called and emailed over the last week with no replys or answers. Thank you.

Looking to buy Shelby engine cap set that was for the 07-09 Super Snakes. This is the style that had the snake emblem on them. Really looking for radiator, power steering and windshield solvent but will consider complete set if available. Thank you in advance.

Does anyone have a picture of where to place a jumper wire to run the heat exchanger pump on an 08? I can't find the one picture I had and pictures via our website as well as others are not very clear. Fighting the dreaded air pocket. Thank you in advance.

After tripping over my Stainless Works long tubes in the garage I thought I would ask this question. Just how truly restrictive is the stock exhaust on the 07-14 GT500's? The most identified part of the exhaust system to be restrictive are the exhaust manifolds. Although they look restrictive...

Has anyone tried JBA's catforwad shorty headers #1565S for 07-14 GT500s? If so how is fitment, quality, etc. thanks in advance.

Does anyone know of a strut tower brace for a 2008 that will clear a KB 2.8. The motor has been dropped 1/2inch as well. Thank you in advance, Harry

After 5 yards of running S/w long tubes and full 3 inch exhaust I decided to go back to my stock exhaust system on my 08 GT500. I cannot get both mufflers to adjust parrell to the ground. The back of the drivers side muffler hangs down further than the passenger side. Is this how they came from...

I am in the process of getting my exhaust ceramic coated. Exhaust manifolds are done, now on to the factory x pipe. I seem to remember reading that the catalyic converters should not be coated because they cool by being exposed to the air. Does anyone know if this is correct? Thank you.

Does anyone know the Ford part numbers for the studs and nuts that hold the catted X pipe to the exhaust manifolds? Thank you in advance.

Silly question but I don't recall anyone discussing this. Has anyone upgraded the u joints and other components on their stock 2 piece drive shafts instead of going to a 1 piece? I made the upgrade to the 1 piece years ago but was just wondering if there were any companies that provided this...

Looking at Magnaflow 16674 or Dynomax 39460. I am trying to stay away from the dreaded drone. Does anyone know if either of these 3 inch cat backs have any drone? Thank you in advance.

For those that have installed lowering mounts did you transfer the rubber dust shield from the old motor mount to the new one? I'm in the process of doing the swap and am wondering. Thank you in advance.

When installing the stock 08 exhaust manifold gaskets does it matter which side faces in or out? One side has the part numbers stamped into it, Thank you in advance.

Has anyone installed a bung in the stock H pipe on a 07-09 GT500 for reading A/F ratios? If so where is the correct location? I am thinking above the drivers side cat but am not sure of the distance between the cat and the manifold. Thanks in advance.

Anyone have any idea at what boost # or HP will aftermarket cats begin failing? Thanks in advance.

I have a 2008 with 4:10 gears. Ran stock size tires for 3 years with zero issues, all was good. I went to a taller tire and now I get a howling, odd sound coming from the rear end when making turns. The tire is not rubbing, or making contact with anything. I am going to add friction modifier to...

Has there been any unbiased, dyno backed tests to see if using the factory mufflers compared to the aftermarket has caused any HP loss? I understand the sound differences but actual loss in performance?