Search results

  1. Jukens

    FS: 2011 Mustang GT Paxton Supercharged

    Looking to sell my ingot silver 2011 Ford Mustang GT that is Paxton Supercharged. Wife and I are looking to start a family and I need to get an SUV. Car has only 22,500 miles and looks amazing. So much done to it and its still under the full factory warranty. 36,000 mile bumper to bumper is good...
  2. Jukens

    Umi antihop kit installed and new noise...

    With installing new lca's and relocation brackets I expected more nvh but is this normal. It sounds like mud tires on highway except only on deceleration. I swear I am getting a new noise with each part I install... http://www.youtube.com/watch?v=xzoSNZaQo4E&sns=tw Not my video but same noise.
  3. Jukens

    Throw out bearing going bad?

    I replaced my clutch a couple months ago but kept my stock tob and have noticed a a slight whirring noise coming from the assembly. It's noticeable in neutral with the clutch pedal out. Here's a video, while running I could see the tob moving in and out but everything else looked good...
  4. Jukens

    Warm to hot start up issue

    Still trying to work out a startup issue I've been having. Here's the rundown. Every morning I startup to go to work and it fires up immediately. Drive 30mins to work and shut it down. Come back to start it 45mins later and it cranks for 4-5 seconds then starts boggy for the first couple...
  5. Jukens

    UMI LCA's...these look right?

    Just received and installed these umi lca's and relocation brackets and noticed that on the larger end of the LCAs it isn't welded center and is longer on one side. Both of them are identical and longer on the same side. Is this correct. I figured they would be opposite of each other.
  6. Jukens

    Crank position relearn needed?

    Seems that since I replaced my clutch and flywheel I have been getting random long cranking startup issues. One of the times it even went the whole time allowed before it stopped cranking. Yet every time I go to start it immediately following the long crank it fires up immediately. I've put over...
  7. Jukens

    Floor vent stuck closed?

    Just noticed today now that it's getting cooler out that I couldn't get any air warm,cold, or recirculated to come from the floor vent. When the air full blast I can hear it switch and it never comes out the floor vent but instead is forced out the windshield vent. Any ideas?
  8. Jukens

    New clutch installed...questions.

    Had to install a new clutch on my blown 5.0 as the stock was slipping quite a bit. Picked up the exedy stage 3 and spec billet steel flywheel. Had helluva time getting the transmission to mount up as the alignment tool with the exedy clutch did not fit the pilot bearing anywhere near snuggly...
  9. Jukens

    My Paxton Install Experience

    Well I finally have my Paxton supercharger kit installed and finished besides getting my vortech pump booster to work correctly. Here's my story: Early June I get the go ahead from the wife. I'm currently stationed in Ft Gordon, Georgia but they have a great shop that I can do the install at so...
  10. Jukens

    Vortech Boost A Pump Priming problem

    I narrowed my cold start cranking issue to my BAP that isnt allowing my fuel pump to do a full prime. When I bypass it I prime for a good 2 seconds, with it plugged in my pump goes on then off but never a full prime and its causing me startup issues, once started it runs fine though. I have...
  11. Jukens

    Paxton 2200SL installed and having problems.

    Installed the kit 2 weeks ago along with some ID1000 injectors and a vortech boost controlled BAP. Been working with Ken from Lund racing with the tune and hes got the wot dialed in but I am stuck with an issue its having even with the base tune. At light throttle acceleration its hesitating and...

Top