Has anyone measured boost drop before and after long tubes installation? I want to pulley down to maintain the current boost of 18psi, just dont know if I should add 1 or 2 lbs back in. I've searched and can't find any answers.
Setup is 2.65 gen3 TVS
Dragon tb
3.3 upper only
ARH 1 3/4 LTH 3in...
Like the title says, has anyone ever ran a stock lower with metco 3.2 alt pulley? I put my stock lower back on due to getting a gen 3 tvs.
Just wondering if it will undercharge or if spinning it slower may actually be better?
Thanks
Sent from my SM-G930V using the svtperformance.com mobile app
I've searched and oddly enough came up empty. Usually I can just search and someone has already made a thread and answered my question. And I posted it here because I'm not sure if it's an engine or drivrtrain vibration. So with that out of the way....
Last winter I installed a cobra...
A few months ago I installed a steeda tri ax and ever since then I get a pretty good vibration in third gear only. It's loud enough to hear and shakes the shifter knob pretty good. All other gears are fine, it gets silent when I put it in fourth.
I did pull out the shift stop bolts.
I also...
I'm nearly done with the cobra engineering m122 swap an it requires the battery to be moved to the passenger side or to the trunk. I'm not wanting to put it back there just yet. I've seen pictures of people who used their stock battery and moved it over, just extended the cables, I'm good there...
Hey do you guys know of anyone besides ford that sells the seal that goes in between the elbow and blower on a m122? Mine is suspect and I'd rather not risk it. Thanks in advance!
I have a set of maximum motorsports xd rear lower control arms I bought slightly used (about 10k or less miles on them) for my gt500 I had, I ended up selling the car and have these left over. These will fit all 05-14 mustangs.
These go for $400 brand new. I'm asking $200 OBO plus shipping. I'm...
I'm looking to buy a vmp or other after market elbow. I have a stock ported one that was over ported and broke into the sealing area. It may still seal however I'd rather not risk it.
Please pm me or post here if you have a used elbow you'd like to sell.
Thanks
I have a set of maximum motorsports xd rear lower control arms I bought slightly used (about 10k or less miles on them) for my gt500 I had, I ended up selling the car and have these left over.
These go for $400 brand new. I'm asking $200 OBO plus shipping. I'm sorry I don't have a picture of...
I'm looking to buy a Hydro Boost setup, I don't need the brake master cylinder or any lines. Mine is leaking like crazy. If you have one you don't need or know of someone selling one please let me know!
I have a JLT next gen Cai I bought about a year ago and put maybe 5k miles on. It's textured black and still has the holes intact for the high boost upgrade. I absolutely love the intake but need a rai due to moving to Washington state and it's wetter here. I'll trade straight across for a JLT...
Ive looked and searched and I can't find a thread where someone has had this problem, which is odd. But anyways, I recently changed my stock TOB out for the FRPP piece and the sleeve with a lethal piece as the stock one was broken. After the install it made a similar sound as the broken stock...
Hey SVTP it's sad but I'm sure you have had similar issues and I'm basically wondering what can I do? Legally? I'd rather just get my parts but I don't see that happening.
Story is I purchased a set of 60lb injectors 10 days ago. I pay pal'd him the funds and every day since then he's made...
My numbers seem a little high, tell me what you guys think. I made 563rwhp with a steeda cold air and sct tune, metco 2.8 pulley, catted x with resonators and I iced the blower a bit. For people with similar mods it seems a bit on the high side. Dyno jet at 4,400 ft above sea level. Tell me what...