**Sold.**
Hi everyone. Please use PM to contact me for the fastest response as I’m not on here frequently. Asking $27,000
I’ve been a member here for a few years now and have enjoyed learning all about these incredible cars from the friendly and knowledgeable SVTPERFORMANCE community. I’ve...
I’ve gone back and forth about selling my car as I never have a chance to enjoy it. Now that we’re dealing with this whole pandemic firsthand (my wife is a nurse) I’m going to end up listing it here for sale but have not yet typed up the ad.
The car is a 2004 3-owner (original owner had it...
I’m going to be putting mine up here shortly. Black 2004 coupe, Teksid build, 2.9 whipple, D&D performance Viper Spec T56, custom DTS SRA and the list goes on. Ping me if interested in additional details.
Sent from my iPhone using Tapatalk
Cleared out the garage last week for a spring cleaning and took this. My DD is a 2014 F150 Platinum. Wife’s BMW X3 in the middle.
Sent from my iPhone using Tapatalk
Thanks guys. That is not too bad. I had asked about this at one of the local shipping stores, albeit using estimates for weight and box size and it was some ridiculous amount exceeding $300.
Sent from my iPhone using Tapatalk
Has anyone sold and shipped a supercharger setup? I’ll be packing and shipping a Roush 2300 setup, complete with lower intake, throttle body, injectors and a belt tensioner/brackets.
I have no idea what it might cost via FedEx and would appreciate any insight.
Sent from my iPhone using Tapatalk
I’m not real familiar with the meth controller yet so I’m not positive on how I would set it up. I do know that it has an adjustable on/off based on 0-5v, which I could signal from either the MAF or MAP.
I’m also thinking of using a Hobbs pressure switch to cut the ignition/injectors off as an...
My car has a triple pump hat in it with a return system. Everything works great, but the 3 pumps are wired with their own relays and run all the time.
Since this is overkill and can lead to fuel heating, I’m planning to stage 2 of the pumps.
The method I’ve seen (other than expensive...
Speaking from experience with a car that had low torque numbers on the dyno due to piston rings not sealing, your torque curve does not look like an engine with any issues allowing cylinder pressure to escape (bad rings, valves etc). That is a solid curve right off the very low end. If there was...
I never had a stock blower/E85 car, but when I was researching before upgrading the blower on my last car, everything I read was making 500/500-530.
Even at that the blower would generate a great deal of heat so that was with a cooled setup on the dyno.
Personally I would be happy with...
I have a stock tensioner and has slipping...ground the stop tab off and bought the metco brace and went back, no issues even at 23.5psi
Sent from my iPhone using Tapatalk
First off let me start with stating the issue so there’s no need to read all details below if your not interested.
My strut (old style Aluminum body QA1 HS603 single adjustable strut with adjuster at bottom) has exactly the same rebound and compression no matter what I adjust the knob to...
Thought I’d pass along some info on shipping. Anyone looking to ship an engine/trans/both etc. you can do so through Fastenal’s 3PL logistics.
I just sold an Aluminator short block and shipped from Michigan to South Carolina for $160, which includes a standard insurance coverage of $5,000...
Bump let me know if any questions. This was built with my current combo in mind (2.9 Whipple 20-24psi E85) with 700-750 rwhp Target, so everything was upgraded to safely handle that.
Sent from my iPhone using Tapatalk
Welcome! If you want to learn all the right stuff from guys who know it, there is a thread on here titled ‘Aluminator build’ by jrgoffin (I think that’s his username).
I was like you, had built lots of Windsor based engines before but never a mod motor so when I found it and read through it...
Sold.
M-6009-A46SC Ford Motorsport Aluminator short block for sale. Brand new fresh from the machine shop but better than new as bearings, rings and main bolts have been upgraded along with piston skirts coated.
Long story short on history of the engine. Original owner popped a head gasket on...
I’ll have a short block for sale here shortly. Aluminator block (the chilled bulkhead cast Nemak), standard bore with various upgrades.
Sent from my iPhone using Tapatalk