Search results

Thanks for the info and link buddy. Can i ask why you don’t recommend this tool for in car use? Thanks Sent from my iPhone using the svtperformance.com mobile app

They make a tool to do it with cams still in place? Sent from my iPhone using the svtperformance.com mobile app

Was gonna grab a bolt on spring compressor tool from eBay Sent from my iPhone using svtperformance.com

Yes sir. Everything done including 5 way valve job Sent from my iPhone using the svtperformance.com mobile app

Hey gang, I’ve decided I’m going to tackle this embarrassing smoking issue i have when i start the car. The engine was completely overhauled about 2,000 miles ago, and it’s done it ever since. I wanted to wait to see if it went away but it’s obvious it’s not going to. I don’t want to say who...

For one of this winters maintenance projects I’d like to replace my radiator on my 03 Cobra. Any suggestions on which one to purchase? I’m looking at a Fluidyne on Lethal Performance but wanted to see what you guys and gals suggest. Thanks Sent from my iPhone using the svtperformance.com...

First off it smokes blue only on start up, Second i scoped the cylinder and see oil puddling, Third i know how to read plugs Sent from my iPhone using the svtperformance.com mobile app

After swapping out spark plugs for the season I’m pretty sure i found my smoking on startup reason. My #5 cylinder valve stem seals are bad. Any way to replace without pulling the motor and removing the cylinder head? It’s the cylinder at the very front by the power steering reservoir on driver...

I ended up finding one guys, but i certainly appreciate it Sent from my iPhone using svtperformance.com

Anyone have a MAC Pro Chamber for sale for Longtubes? Sent from my iPhone using the svtperformance.com mobile app

Anyone have a MAC Pro Chamber for sale for Longtubes? Sent from my iPhone using the svtperformance.com mobile app

About how much free play should be in these clutches in your opinion? Sent from my iPhone using the svtperformance.com mobile app

Hey gang. I recently upgraded my blower to a KB 2.2 from my ported Eaton , also i had my Tremec T56 overhauled and 26 spline installed while i had it out which means i also picked up a new 26 spline clutch disk and while i had it apart i also grabbed a new flywheel and stock OEM clutch cable...

Thank you buddy Sent from my iPhone using the svtperformance.com mobile app

Leaking from seal, not the plate. I keep reading about this “oil slinger” but i don’t know what it is. I don’t think my engine builder installed it because i replaced the seal once before and i didn’t see anything but the seal there. But then again i don’t know what I’m looking for. Is it...

Well after getting my engine completely overhauled and that brand new RMS started leaking, i changed it last winter and after driving it all summer now this one is leaking. WTH is going on here? Anyone else have this issue before? I have crankcase vents on both sides too. The seals i used were...

Thank you

No it came out of nowhere

They did supply me with the harness and when i asked them what the extra blue wire was for they said it might not be necessary for me to hook it up so i didn’t

Hey gang, last night for the first time i noticed my battery light coming on when under a hard pull and close to top of RPM band. My alternator is a Mechman billet 240S with only about 1,500 miles on it. I refreshed my entire motor 1,500 miles ago and went fuel return also. I’ve never noticed...

Thanks for response sir. I did use the PTFE line for the return line Sent from my iPhone using the svtperformance.com mobile app

Hey gang, this past winter in installed a Kenne Bell and a Lethal fuel return system. Everything turned out great and the car is a blast, however I’m getting a strong fuel smell now. Everything is tight and no leaks that i could see and no drips on the ground and filler neck gasket on tank is...

I’ve been doing research on how to set the spacing and from what i found you want the spacing between 1/4 to 3/8 from bottom of pick up tube to pan, but it’s never said if that measurement is from the edge of the pick up tube ( lip) or the screen itself . The screen sits a lot higher and i don’t...

Hey gang, I’m still in need of a MAC shorty midpipe for MAC Longtubes. At this point I’ll take anything, a Pro Chamber , H , or even an X pipe even though i really don’t like X pipes . If anyone has one they’d wanna sell please let me know. Thank you all Sent from my iPhone using the...

Any Lethal Discount codes today for orders over $500? Sent from my iPhone using the svtperformance.com mobile app