Search results

I am looking for a little help. I am in search of a metal Montana Ford dealership license plate frame. I don't care what dealership or what city as long as it's Ford. If it looks weathered, that's cool. I prefer metal for longevity. I'll be getting my Montana licenses plate soon and just...

I installed a MMKM-2 K-Member and installed the control arms in the highest mounting point. I thought that this would provide me with some extra room for lowering or at the very least have the control arms in a more positive orientation (positive meaning engine side higher than ball joint...

I am in the process of building an Aluminator engine. I go to purchase the main bearings I am going to use, MB5281SI STD and I can't find them anywhere. King apparently is back-ordered on these for 8 weeks. I wanted to use these as I am going to go for the fully flanged rear mains (using the...

OK. A bit of a rant here... I am just finishing installing my new MM K-Member. I had installed brand new Prothane 6-504 motor mounts since the K-Member was out. I am installing the nut on the passenger side @ 95 Ft Lbs and the thing just snaps off. WTF? I called Prothane. They said they...

Delete. Found a Teksid instead. Thanks.

Need help! Installing thse on my 2003 GT. I am stuck on the passenger side. How the hell do you tighten the nut that is above the second exhaust port (counting from the front)? There is absolutely no clearance to get at it.

I have a line on some new Trick Flow TFS-51910001-M-38 heads. I don’t need them right now but the price is so good that I am looking at getting them for a future build. I have seen some threads that mention fitment issues with Kenne Bell but it is never an actual owner and never specific...

I am pulling my oil pan to fix a leak. While I have it off, it is the perfect opportunity to inspect the bottom end. Only problem for me is that with everything assembled, I am not really sure how to really gauge the health of rod bearings or crank bearings. Are there any visual ques that I...

2003 GT T56 McLeod RXT McLeod Lightened Steel FW Stock fork Stock Pivot Stud I did a T56 swap. The transmission came with an McLeod RXT. It is installed and working properly. However, I have clutch pedal releasing at the top of the stroke. I want this closer to the bottom / stock release...

I installed a T56 into my 2003 GT at the end of last November. At that time I also installed a reverse lockout module. I haven't done anything with the car until today to finish up the job. The last thing I needed to do was to install the switched 12V that I picked off of the cigarette...

2003 GT Kenne Bell 2.1 Magnaflow 441114 I am getting ready to install an Innovate PSB-1 AFR meter. I just installed a new CARB approved Magnaflow 4-Cat exhaust (because of the crushing smog inspecting here in California). This is replacing my Magnaflow 2-Cat x-pipe. With the Magnaflow 4-Cat...

OK, so this has been a topic of conversation lately. It seems as though CA has kicked up its smog screening noose another notch. Cars are getting failed at smog even though modifications are CARB EO and self test monitors are all showing ready, all cat monitors on. Only thing that is...

I live in California and suffer under the oppressive emission Nazi regime. I am getting hassled because my emission decal that is supposed to be under the hood is missing. They said that I could go to Ford and get a replacement. Ford says they do not have them for cars that are older than 10...

Are the SN95 / new edge stock self adjusting clutch quadrants still available? If so, what is the part number? I can’t seem to find a set anywhere.

I am installing a used T56. The end play looks OK as far a I can tell. Very, very minute in-out end play (almost undetectable with out an indicator) . However, there is a fair amount of lateral side to side / up and down movement. As best I can measure with my McGyver'ed digital indicator...

I am currently using Allstar 42151. This stuff is very,very stiff. If you are running brake ducts, what hose are you running that you like? This will be mostly for HPDE. Almost no regular street driving.

I am installing brake duct cooling on my 2003 GT with Cobra bumper. I purchased Allstar Performance AAF-ALL42151. Man, this stuff is super stiff. I want something that will be robust but still need good flexibility for routing. Let me know what you recommend.

I am installing brake duct cooling on my 2003 GT with Cobra bumper. I purchased Allstar Performance AAF-ALL42151. Man, this stuff is super stiff. I want something that will be robust but still need good flexibility for routing. Let me know what you recommend.

Upgrading the rear brakes on my 2003 GT to Cobras. Looking for the cobra caliper mounting brackets and anti moan brackets. Don’t really care what they look like. Not looking to spend a fortune. I’ve seen some really crazy prices on the web...

Upgrading the rear brakes on my 2003 GT to Cobras Looking for the cobra caliper mounting brackets and anti moan brackets. Don’t really care what they look like. Not looking to spend a fortune. I’ve seen some really crazy prices on the web...

Looking for a larger MAF for my car. Would love to find either a BA-2400 or BA-2600 as soon / inexpensively as possible. Let me know what you have.

Time to replace the fuel pumps. I am looking for stock replacement. The Motorcraft are crazy expensive. Is there a direct replacement that flows the same LPH but easier on the wallet? Thanks!

I am setting up a 2003 GT for track use. It will be driven to and from track events but not a daily driver. I will be doing HPDE for now and will see where it goes from there. The car is almost ready to go so I need to start figuring who I will HPDE with. I am in northern California and will...