Those were the days! Before Savi Ranch got big there was a regular gathering of Cobra's at the Cup in Aliso Viejo.
Looking way back to 2001-2002'ish I used to hang on StangNet. A member named Stormin Normin with a black new edge cobra would organize big cruise events.
RIP to this forum. Hopefully the FFF show continues for ever. They used to have a cool surf guitar band every year called The Torque's.
One year Dallas Raines of local TV weather fame showed up in a beautiful silver De Tomaso Pantera.
I have an old DSS lvl 5 half shaft which needs some serious repair work.
One option is to ship to DSS but they are on the opposite end of the country.
It seems like there would be a local shop that refresh the CV's and check the shaft for trueness.
The rear axle on my 2013 was removed/re-installed by a body shop and now the car rides like garbage. Talks with the body shop have broken down and taking the car back there is no longer an option. Springs appear to be seated properly and everything seems tight. Any ideas? I'm thinking it is time...
Local sale preferred, parts are located in Fullerton. PM me any offers, I need to get rid of this stuff. I am also looking for SN-95 lowering springs and suspension parts.
Stock 03 reservoirs
74.5 inch belt, never used
Set of stock 03 cobra coupe springs and iso's
JLT CAI...
I have a 98 GT that has gotten really loose in the front after 120k miles. The car is reilable daily transportation so I've decided to spend some money getting it to drive a little better. At the same time, I'm not trying to spend any more than necessary, I'll save that for the Cobra.
The...
I have my stock cobra coupe rear springs lying around and my 98gt is really in need of some rear springs.
Can I just chop them and toss them in or is it a completely different style of spring?
I am wondering if it would be safe to remove my chip so I can limp the car down the the smog check station. I failed an emissions test even though the car has stock cats. I'm pretty sure the car will pass on the stock tune. Will my car run too poorly or throw a CEL without the chip in?
If I...
2.8, no lower
Posi port, self ported accufab plenum and self ported lower intake
accufab tb
home made intake
cat back
RET tune
513rwhp 485rwtq
I was impressed especially considering the car has stock cats and runs on 91 octane.
Also I can't say enough positive things about my...
I'm about to purchase a wire upgrade kit since I bought a used BAP with all the wires cut.
My concern is weather or not the wire upgrade will work ok with the 30 amp version of the BAP.
Also, I don't have the controller knob, it is possible to wire things up without this piece?
thanks!
I'm looking for any ideas on why I can't surf to SVTP on any computer connected to my Road Runner cable modem. My connection is working fine otherwise. I can get here using a proxy site or through a VPN.
I've tried reseting my cable modem and I've taken my routers out of the loop to rule them...
Lethal is now selling a PFAB radiator coolant reservior.
PFAB 96-04 Mustang Radiator Coolant Expansion Tank [PFAB-9604CET] - $240.00
Does anyone have one of these? Any pics? I think my money would be better spend on a bigger radiator but these just look so cool.
My motor is making a loud noise, similar to a rod knock.
It only occurs when the engine is hot, and has just been driven.
The knock goes away after the car idles for a few minutes, and returns after the car has been driven again.
I have checked all the easy stuff:
Oil and coolant -...
JLT CAI
stock MAF w/Mafia
Accufab TB/Plen
Steig. Stage 4
2.8 upper, stock lower
cat-back
Would a BAP or injectors be a good safety measure or overkill?
Some people (including Steigmier) state that no fuel upgrades are necessary but other have said that this combo is close to maxing...
My Rear MM Bilstein coil-overs are noisey when going over small sharp bumps.
I've noticed that when the car is in the air, the upper spring perch is loose enough that I can jangle it all around.
Do you think this could cause the noise I'm hearing?
Suspension is unloaded in this picture.
I made a little road trip to Aera 51 to help Wurd2 install his long tubes. I came back with a few neat pictures.
kook's
Mach
500+ cubic inch, all aluminium, solid cam, 13:1. One with dual carbs, the other injected. My uncle said they each make four-digit power figures. I coudln't...
stock 03 cobra springs/shocks 30k miles
stock 03 throttle body/plenu
just need this stuff out of my way. offer me a few bucks and come pick up
Rowland Heights