Search results

FYI for anyone that might be looking for this info in the future. Supply 12v to pin 41 from your ac pressure switch, then ground your compressor relay on pin 69, that’s it. On my datalog last night when I do this the compressor activation is logged, I see the rpm adder for AC signal increase...

I've dropped an 03 Cobra engine into my 1970 Mustang. I'm using a detail zone engine harness for the car. Everything is wired up and working great, except for when I turn on my AC the engine doesn't know it's on so it idles down low and will stall out sometimes. I'm trying to understand what...

Thanks for the responses guys. Guess I should have added a little more detail. I’m not tuning the car myself, using a well known tuner for remote tuning. Datalogging signals per his request, sending him logs, uploading turns as needed. The car is actually a 70 Mustang, running a detail...

Anyone good with reading datalogs? Got an issue with my car stalling out with the AC on when you close the throttle from like 2k rpm or higher. The engine just almost immediately stops. This can happen sitting in the garage, so no load from driving. When looking at data logs, the only...

Hey all, I'm going to be relocating to the NorCal (Palo Alto, San Jose, Fremont) area here in the next couple of weeks. Was wondering if there were any local car forum sites to join to get in with the local car scene? Initially I'm going to be bringing my 1970 Mustang Fastback project with...

I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. 1 - new Greg Weld Racelite 15x3.5, 5 lug (4.5 and 4.75") chrome wheel including center cap. Looking $100 shipped...

I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. Stock 3.31 Rear gears, only have 5K miles. $45 2 Walbro GSS 392 external 255lhp fuel pumps. Both come with...

I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. Stock 3.31 Rear gears, only have 5K miles. $50 Stock Transmission crossmember - $50

sold

I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. Stock Fan assembly - $65 for the fan Stock Pulley guard. In really good shape, barely looks installed. $45...

I purchased a used blower a while back that had a 2.8" pulley and hub assembly on it. I'm looking to get a 2.93" pulley for the setup, but I'm having a hard time locating a pulley that will fit the hub. My current pulley has a 33mm hole in the center of it. 4 bolts attach the pulley to...

Anyone got a stock trans mount they would like to sell? If so, send me a PM with price shipped to 46033. Thanks

Not sure if any of you have seen it or not, but the track is flooded really bad. By the pictures I would say there is at least 15ft of water on the track, maybe more. Hopefully they can recover from it quickly. Local Racing News and Rumors by ODELL: POSTED 5-3-10 FLOOD OF 2010 AT BEECH...

Anyone done an IAC relocation on their car? I'm doing a custom install where I would like to remove the IAC from the top of the plenum completely. Would it be as easy as just plumbing a port from before and after the TB to a plate where the IAC installs? Thanks in advance.

White 10lb NX bottle - $100 + shipping 10lb NX bottle that has been professionally painted back. Very glossy, some minor scratches/scuffs from being installed in brackets, great shape otherwise. $150 + shipping If local each bottle still has 3-4lbs of nitrous left in them. If I...

1 - new Greg Weld Racelite 15x3.5, 5 lug (4.5 and 4.75") chrome wheel including center cap. Looking $100 shipped for it.

03 Cobra TB/Plenum/Injectors Adapters/Rails I'm in the middle of a move right now, parts are packed up in a trailer and I won't have access to them for at least a couple of weeks. I will post when they are available again. Spring cleanup on my garage. All parts below are off a 32K mile 03...

1 pair - Weld Draglite XP wheels, 16x9.5 with 5.5" backspacing. They have 26x11.5x16 ET streets installed on them right now. The wheels are in pretty good shape, do show some minor corrosion on the outside lips, probably will buff out. The ET streets are almost new, TONS of tread left on...

Wet NX Nitrous Kit, SOLD The NX automatic heater SOLD White 10lb NX bottle - $100 + shipping 10lb NX bottle that has been professionally painted back. Very glossy, some minor scratches/scuffs from being installed in brackets, great shape otherwise. $150 + shipping

1 - new Greg Weld Racelite 15x4, 5 lug (4.5 and 4.75") chrome wheel including center cap. Looking $100 shipped for it. 1 - new Greg Weld DragStar 15x4 SOLD 1 pair - Weld Draglite XP wheels, 16x9.5 with 5.5" backspacing. They have 26x11.5x16 ET streets installed on them right now. The...

Spring cleanup on my garage. All parts below are off a 32K mile 03 Cobra. I got the drivetrain out of the car, these were included. I'm not using them on my project, so they are just taking up space. Reply or PM me if interested. Prices are obo, but no low ball offers, I'm not in a hurry to...

I've got a complete 96 Under dash harness for sale. Don't think it is missing any connectors or anything. Don't have a picture right now, but can probably take one this evening. $40+shipping I've also got a complete 97 MKVIII Motor that I'm parting out. Everything is available except the...

I'm needing an IAC for an 03/04 Cobra. If you've got one, let me know. Thanks Todd

Will a pair of 16x8.5" with 5.5" of backspacing fit the rear of a 03/04 Car with IRS without grinding? Will they have clearance issues with the fenderwell on a lowered car with 26x10.5 ET Streets on them? Thanks!

Will a pair of 16x8.5" with 5.5" of backspacing fit the rear of a 03/04 Car with IRS without grinding? Will they have clearance issues with the fenderwell on a lowered car with 26x10.5 ET Streets on them? Thanks!