Search results

So the clutch finally went in my 04 Cobra, and I need some recommendations on the best Flywheel/clutch/TOB combo that would be best for what I use the car for. I had some nightmares with my 99 Cobra using different manufacturers for some of those parts. I also had issues with using a non-Ford...

Does anybody know which circuit board stores your mileage? The mini board that has the odemeter plug? Or the large board that houses your lights/connects to the gauges etc?

New Terminator owner here. I was going through the EZ pass toll last night, so probably rolling through in 3rd gear at about 35 mph. When I gave it some gas exiting the toll, not a lot, just accelerating back up, the car lurched and fell on it's face for a brief second, like I hit the rev...

Up for sale is a set of (4) 17x9 OEM Ford Mustang SVT Cobra wheels powder coated in Kingsport Gray with (4) mounted and balanced 275/40/17 Goodyear Eagle F1 tires. The wheels are flawless and have no curb rash, no damage, and run perfectly straight and true. I have a receipt for the powder...

I just sold my 99 Cobra and I had bought replacement seats for it a while back. Since the drivers seat was the only one in rough shape I didn't end up replacing the passenger seat and just kept it as a spare. So here it is for sale, in great shape, $100

Hi All, I recently sold my 99 Cobra so I'm getting rid of all the extra parts I had laying around in case I needed them. All parts were functioning properly when removed. All parts came off my 99 Cobra except the AC compressor and power steering reservoir, which came off a 03 Mach 1 when I...

The 03/04 Cobra envy is officially over for me! After 13 years, 169,081 miles (245,581 total miles), 1 engine rebuild, 1 engine swap, a few clutches, and a very extensive list of repairs/mods, both successful and unsuccessful, I did what I never thought I could, or would, and that's get rid of...

Looking for an 03/04 Cobra coupe with bolt ons or closer to stock in the New England area, but I could venture down as far as New Jersey or Pennsylvania if I found the right car. Looking for something $20k or below. The only color I wouldn't do is red, everything else is in play. PM if you got...

So my throwout bearing failed back in October of last year and I finally got around to replacing that and the clutch. The car sat in the garage for those 8 months without being started. I rolled it out of the garage after the clutch job and hooked the battery back up. The car cranked strong...

For a while now I've been collecting fresh oil on the oil pan bolts, bottom of the oil pan, engine backing plate, and bottom of the bellhousing. The front half of the oil pan does not have much fresh oil on it, it only shows up on the back half near the tranny. Just estimating I think I lose...

With 230k on the clock and rising (99k on the engine). I took the cobra to the dyno and was pleasantly surprised. Mods are in my sig

***UPDATE*** Last August I spun (4) rod bearings in this motor. I've taken it completely apart and I'm looking to get rid of everything here. The engine ran smooth and normal even after the spun bearings so there was no other damage that I can tell. It came out of a 99 Cobra. The crankshaft...

So I've done some poking around and it seems popular opinion is that a 2003 mach 1 engine harness will not work in a 99 Cobra. I have a complete mach 1 engine with harness ready for transplant, but I still have my 99 harness. The only visual differences I noticed was the sensor on the mach 1...

Ok here is a good one. ***UPDATE: VIDEOS OF NOISE POSTED BELOW*** The other day during some spirited driving, I shifted from 1st to second at about 6200 rpm and for an instant I felt a loss of power in the pedal and then came a metallic rattling/knocking noise from the engine. I'm calling it a...

The front seats have two studs holding the track in the front, and two 10mm bolts going through the floor in the rear. In the process of swapping seats one of those bolts broke off, and in the process of trying to extract the bolt, an ez out broke off in it. There is a plug welded...

Whenever I start the car for the first time cold, I get a loud (what sounds like piston slap) noise for 2-3 seconds and then it vanishes. If I shut the car down and try starting it up a few minutes later the noise is diminished and barely lasts a second. This is the only time I ever hear the...

Ok, I've got a horrendous grinding/howling coming from the front of the car, it easily drowns out my exhaust which I never thought was possible for any noise. It goes away completely when I turn the wheel left so I figured that it was definitely my drivers side wheel bearing that was making the...

I've noticed oil under the drivers side exhaust manifold near cylinders 6, 7, & 8. Nothing too crazy, but looks like a good steady leak. Everything above the manifold is bone dry, perfectly clean. I had the car at the dealer for an alignment recently so I asked them to take a look. They did...

This has probably been covered, but just in case it wasn't I thought I'd share my experience. I had this bearing noise coming from the accessories, and with a screwdriver to my ear, 100% of the noise seemed to come from the alternator. I checked everywhere else and I was positive it was an...

So, I bought a set of the March Performance underdrive pullies and searched this forum and got all kinds of good info on the details and install so off I went. I got the alternator pulley off, water pump pulley off, and finally the crank pulley off with the typical 3 pronged puller...

I did some searching and found that many New Edge owners, like myself, have a cracked cowl vent. And also like me, they can't stomach shelling out $200 for the damn thing. I'm trying to hunt down a vibration noise and didn't know if anybody else had experienced any noises emanating from these...

For quite a while now I've had this annoying metallic ringing noise coming from the drivers side front (could be somewhere in the dash also). It has nothing to do with RPM's or load on the engine. It basically occurs above 60 mph no matter what I'm doing so it's some type of vibration. It is...

So I was just finishing up my clutch job and the last thing to go back together was my mid-pipe, and one of the nuts on the passenger side is getting hung up on the stud threads. Everything had been going smoothly up to this point so I should have known my shit luck would kick in at the very...

Well I fried my clutch at the drag strip last week, and I'm planning to do the job this Saturday. Just looking for some feedback on the prices and parts I'm getting. Wanna make sure I'm not forgetting anything on the parts list, or paying too much. From what I gathered on a post search, the...

My passenger side valve cover gasket has been leaking so I'm planning on replacing it in the next few days. I took a quick look under the hood today and it looks pretty straight forward. But I noticed the fuel line only clears the cover by a few inches, among a few other things back near the...