Search results

2010 GT500 with just over 10,000 miles. I have invested well over $20,000 in mods. I am the original owner, ordered it in 2009. Never seen weather. Very clean car, always garaged and covered through winter periods. Fully loaded, all options except shaker 1000 (couldn't get with nav)...

I am turning up the boost at the next midnight drag. I still have a stock 2 piece under my car. Up here where I race is a different monster than most of you are familiar with. Our adjusted altitude is often around 7500 ft. At about 20 psi I hope to put down about 760-780 (corrected) RWHP...

Full set of 2010 GT500 seats. 6700 miles on the car. rears out of 2012 car, virtually no miles(from billet pro shop car). Perfect Condition (dropped)$2000 shipped obo

For sale are Recaro skins out of a 2012 GT500 with red stripes. I was planning on using these for my car but found some seats instead. Front skins only. excellent, will post pics tonight. (price reduced)$550 shipped obo. boxed and ready to ship

I paid $55 plus shipping a couple months ago. Never installed. $50 shipped obo

Like it says. Looking for a drag set up for my gt500. Because i have griggs coil-overs, i need 16" wheels to clear the mounting area. thanks benny

I have a takeout Torsen T2 for sale. This is from a 2013 GT500. This is the same Torsen as the '12/13 Boss 302's, and also FRPP M-4204-MB. This unit has less than 500 miles on it, and is like new. It's in perfect condition and functionality. This will fit all 05-14 Mustangs with a reasonably...

does anyone have ARH long tubes, off-road x, and magna flow street series on their shelby? i have searched and read through lots of older threads/posts, and i can not find any of this exhaust combo. this is the combo i just bought, but it will probably be a couple months before i can swap it...

Looking to buy 2 sets of Ford GT Supercar cam shafts. Preferably new, but used is ok too. thanks, benny

i have a whipple 2.9 on my shelby and am gearing up for an arh header/complete exhaust install. here is my plan: i plan on doing this on a lift with a screw jack to raise the engine/trans slightly. i will do 1 side at a time, starting with the pass side. remove the starter, and motor...

i currently have a 100% stock exhaust on my 2010 gt500. i also have an frpp 750hp whipple. i am considering doing an arh longtube set up for a 2011-2012 car so i can run the newer factory (2.75" diameter??)over axle/mufflers and updated hangers. is there any differences in 02 sensor...

I am looking into a new differential for my 2010 gt500. I love the road course, so I am interested in torque-biasing differentials, but I go to the drag strip on slicks once or twice a year. I have seen t2rs break down there. I talked directly to torsen, and they said that the stock diff in the...

these are of my 2010 gt500. car had 2200 miles when i took them off. includes calipers, pads, lines, rotors, and shields. $650 shipped to lower 48

got a screaming deal on some falkins, so i had to buy them. powder coated some 07s and here's what i have... now i don't have to wear out my 19's on the big course

new in the box drilled and slotted front rings from baer. normally $219 ea from baer or shelby $325 shipped

Ford Racing Performance Parts - [Part Details] had it on my car for 800 miles then went with a new blower. still in ford racing box $50 shipped

i want to hear from those that have experiences good/bad with it. last night a friend and i finished the install just waiting for the procal with tune to see how it runs. i never liked the ngk tr7 with my old turbo car, but they were part of the kit.

i have never seen an option for a nice rear caliper for a mustang. i see brembos on all sorts of lame dodge products but never on a ford vehicle... finally the 2010 super snake has available 6 piston rear calipers i haven't seen pricing yet, but i'm sure they are expensive. and i want a set

i just bought a 2010 shelby, and i have been looking at doing the ford racing set up that converts the suspension similar to the shelby gt's. lowers the car about 1.5". i am wanting the car to handle better and look good. the big hang up for me is all the kits seem to leave the rear higher in...

sold

it's time to cut it loose. this is hard because this car is so clean and even more fun to drive. this car has been in the rocky mountain mustang round up in steamboatsprings the last 2 years and took home show prizes both years. i am just outside if slc ut. please no trades at this time...

first time out on a road course, infact the first time i really got to drive my car hard. what a blast, i can't believe how late i can brake coming into corners, and coming out at 80... a friend that talked me into going

i just spent a day at millermotorsport park and decided that i want some good rubber on the R. i still have the original kd's on there now and want to pull the factory wheels/tires off and store them. i am looking for a tire that performs on a road course but is still a street tire. i had...

do all of the 2000 r cars have the monster alt pulley? in the book some of the pictures showed regular sized pulleys. i have the monster pulley and headlights and power windows don't mix well...

been watching these for about 8 months, finally got one. i came home to this after a week at the rocky mountain mustang round up, what a great week