Search results

http://www.ls1.com/forums/showthread.php?t=41474

test

I searched for a HE on a couple of boards. I looked on Fluidyne's website but they don't have their new HE listed yet. I looked at their contact information and found out that their plant is in Mooresville, NC and I live about 30 miles from there. I called and asked if they would sell dirrect...

I finally got rid of the Eibach Pro Kit springs on the front and replaced them with Maximum Motorsports coil-overs with 10 inch 325 pound springs. The car was just too low and rode too rough. I have worked on another 03 with another brand of cheaper coil-overs and it sounded like someone...

There was a yellow 05 GTO running at Shadyside in Shelby, NC last night. I thought, just my luck my 03 is in the body shop after I was t-boned in a parking lot. I met an 03 Cobra owner a couple of weeks ago and since I have a rental car I took my ET Streets down so he could try them out. The...

I'm about the luckiest person in the world. Usually. I got layed off last year and came out smelling like a rose. But, trouble comes in threes and the last two weeks have been one of the worst stretches I have had in awhile. I posted a question last night looking for recommendations for a...

I swapped out my two pound lower for the four pound to go with the 15 upper a few days ago. My Cobra has felt like it was sucking dawg balls lately. I wanted to dyno it to see if I had a problem. I haven't ran the KB yet and it's been over a year since I ran it and I wanted to check the A/F...

Here are a few pics of my Recaros and MM rollbar. I ordered a set of Cobra Misano L's back in late June. They gave me a 6-8 delivery. After 8 weeks they said it would be 2-4 more weeks. After four weeks they said it would be another 6-8 weeks and they didn't sound confident. I cancelled...

I'm just about finished installing the KB on Pumped03's Cobra and ran into a couple of problems. The first one is the PVC hose from the driver's side will not reach the large bulb. I've looked at the routing. It looks like the only thing to do is go to Autozone and buy an elbow about three...

Just finished installing an AEM Gauge Type UEGO Controller to monitor A/F on Pumped 03's Cobra. This is a nice unit. It also has a digital display along with an LED readout. I'm well into the KB install on his 03. Got the BAP mounted and wired. I have the lower intake cleaned and sat back...

I caught the last seven minutes of it on The Discovery Channet tonight. The title of the show is Extreme Mustang: Back to the Track. It is about a tuner race car built on a joint effort between Ford Racing and a tuner company. They were running the car against a 99 Cobra to check performance...

Since I have a little free time on my hands, I'm thinking about ditching my JBA headers for a set of Kook's long tubes. How is the fitment especially around the k-member? Do all the runners exit out the back of the k-member and none wrapping around it? Do the runners require any...

I installed the Steeda stuff this week. Ever since I put in the new D&D TOB and their revised retainer my car has been hard to get in first and reverse especially when the car is hot. It made a world of difference. I wished I hadn't waited. The only thing I didn't like was the quadrant has...

Here are a few pics of my Maximum Motorsports roll bar. I varied from MM's install instructions. They have you assemble the hoop and the rear braces and then drill the mounting holes for the foot mounts. Then they instruct you to carefully remove the bar from the car and weld the rear braces...

Pumped03 has been having problems blowing the FPS's for a few months. The car is not a daily driver and has blown 5-6 sensors over 1000 miles. I've been trying to figure it out. He has a 2.80 upper and six pound lower and a chip for his mods. Here's a chronological list of events. 1. Car...

...........Blower Fund for these. I was laid off the first of this month and my 03 is a daily driver so rather than risking damaging my engine with a KB or racing it I decided to do a few appearance mods while I'm off for a few months. I ordered these from www.hmsmotorsports.com in...

A buddy is having trouble with his 03. Is it possible to swap the computer from my 03 to his 03 when they have the same code number?

I drew this up when Willie was in the Lewinski mess. Since I'm in semi-retirement I plan to create a few cartoons at the expense of liberals. I have a damn good one in my head on Michael Moore. I'll have it on paper soon.

Here are three pics of the line lock install. I mounted it underneath the ABS so it would be a little easier to get to especially if you have big hands. Joe Lynch's instructions mount the solenoid valve on the ABS bracket but the 03 has the IC lines that reduce the amount of room to work...

Anyone install line locks on an 03 or probably a 99 up would work? I've got two 03's lined up for me to install.

Those with TOB/retainer problems, please post a brief history of your problems. Please inlcude your build number and the approximate mileage when yours gave up. I'll start. Build no. 21 of 8394 coupes. Delivered on June 8, 2002. First week of delivery, 200 miles - Bearing started...

Does anyone know what causes the diaphragm in the fuel pressure sensor to fail?