Two problems.
First my dash guage for the oil pressure on my 03 cobra isn't working. Just stays on the 'L'. Where is the sensor for that and what should it read?
This leads to my next problem. I thought I would hook up my DashDaq and see if I could read the data from the sensor. Try to...
My convertible top is leaking. I think I found some cracked spots on the lower part of the top by each corner of the glass where the top folds. At least I'm assuming this is where it leaks. Can this be fixed or is a new top in order? Where can you find OEM tops?
I'm doing a build on my 94 cobra. I need the following items. So if anyone has any stuff they need rid of before I purchase. I'll take better parts. Just let me know.
M-6397-A302 Bolt and dowel kit
M-7560-E302 Ford racing clutch kit
M-7548-A Throwout bearing
M-7600-A Roller pilot bearing...
I'm looking at rebuilding my 302. The rings are shot. Looking for a few suggestions. I have a powerdyne on the car. Y303 P&P heads. If I am going to take it all out and redo it, I might as well upgrade a thing or two. Should I change the stock cam? Should I stroke it?
I have a slightly used Tri-Ax, maybe 5k miles on it. Includes the relocation kit and the CobraBob gasket(new).
I have a DenseCharger CAI with good filter.
Make offers. Decent ones.
It was my understanding that the Shelby Cobra is built on the same production line as the rest of the Mustangs in a Ford Plant.
My local dealer is trying to claim they send these out to Shelby for modification. He argued with me pretty good. He is the new car sales manager, and I am a Ford...
Just like the title says. 04 Rear Driver Tail Light. These were off my mystichrome. I have only the drivers side left. They will fit any new edge mustang or Cobra. Most of the wiring is there and all the bulbs. Factory Ford part.
Would like to get $20 shipped.
This is the housing, no electronics. It is 65mm and calibrated for 24lbs injectors. This is an original Ford unit.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=010&sspagename=STRK%3AMESE%3AIT&viewitem=&item=200054254516&rd=1,1
This is the t-56 for the 03/04 Cobra. Has the relocation kit included and a new set of Cobra Bob's gaskets.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=200054258922
I have a used Metco Lower Pulley kit. I used this on both my Teminators. I have both the 4lb and 6lb rings. I have the 3.5" alt. pulley. I have a the serpetine belt used on the alt pulley and 6lb ring.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=200050507814
94 Cobra, supercharged, the PVC keeps poping out.
First of all what denotes a bad PVC? It rattles when you shake it. So I assume it's good.
I had a breather on the VC. But I really didn't like it. I replaced it with the cap. Now the PVC is blowing out. So I am pressurizing the...
I am selling my Predator.
It's on eBay.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=010&sspagename=STRK%3AMESE%3AIT&viewitem=&item=200045802220&rd=1,1
Thanks for looking.
Looking at a Predator for sale that includes 8 custom tunes. Guy took it off his car and is selling it. He said it is reset or unmarried so that shouldn't be a problem. My question is, can I actually use the custom tunes he is including? Don't want to give anything extra for them if they are...
I have a 94 Cobra. 5.0l. I am going to install new 36lbs injectors. I know I need to get the mass air calibrated or get the chip reprogrammed.
But until I do that, how bad will the car run? Will the car run? Will it just dump to much fuel or what is the result?
I got some noisy idler pulleys. Stock ones. There are two upper stock idler pulleys. Had some squealing, so I figured out which one and replaced it. About two weeks later the other upper idler pulley starts squealing. I replaced it. Not even 5 minutes go by and the new one is squealing. I...
I just got my bracket from SonicBlur installed. I didn't know how I would like the kit, but it works good.
Only thing I didn't like was, it touches the underside of the front air dam and will eventually rub the paint there. So I put me some rubber on it so it wouldn't rub so bad...