Search results

Anyone have the part number for the threaded SAI fitting that screws into the front of the exhaust manifolds? Or know where to get them? I'm not finding anything with Google. I have a set of stainless steel headers that do not have the SAI ports. I want to install the headers but don't want...

Does anyone have full exterior LED lighting (headlights, turn signals, tail lights) that could post some pictures? Also your thoughts as to if it's worth the change cost-wise and your experience specifically with headlight brightness. I'm about to order new headlights (clear with black...

Used but good condition 3" offset in/out Super 44s part #843048. These are the black coated 409 stainless steel. No dents, just some light scratches as seen in the pics. Asking $130 for the pair. Local pick up in CT or I can ship them on your dime. Paypal, Zelle, or Venmo. Calculate your...

I got the car back on the ground with an eyeball alignment so I could take it around the block. Looks really good lowered now. However, the ride height is off side to side. In the rear the passenger side is about 3/4" higher than the driver side rear. The rear is new MM extreme duty...

I'm installing the MM CC plates and have some interference with the line in the picture on the passenger side. The strut install is not complete yet and the car is not aligned yet, but I see the potential interference already. Is this normal, do I need to move this line? It looks like the...

Not doing well with car mods lately.... So, I'm installing my springs, MM CC plates, struts and somehow as I'm REMOVING the strut nut on my Koni yellows to add another spacer and it cross threads or something so bad I can't get the ****ing thing off. It got to the point where I had an 11mm...

I'm installing my MM panhard bar. I CANNOT get the 3/8" drill bit through the frame rail (instructions step #42). Im leaning into the drill hard as hell, going on 15min on one hole. I tried a DeWalt titanium bit (like new) and a brand new Milwaukee Red Helix Cobalt bit, spraying WD40, won't...

If anyone has Stainless Works LT headers could you break out a tape measure give me then center to center distance between driver side and passenger side collectors? I'm looking to get a set for my 97 Cobra and will need to do some fab work to get the 3" collectors to mate to my 2.5" Bassani x...

Anyone run a bullet muffler or resonator in place of the catalytic converters? Reason for the question is I installed the catalytic converters to see how the car sounds instead of the off road x. I actually like the sound a lot, it removes the trumpet "blaaat" sound i'd occasionally get. But...

Anyone know of a good body shop that has experience rolling quarter panels and fenders for tire clearance? Thanks

Anyone running 19 inch wheels? What has your experience been driving and fitment wise? I found some I really like, but wasn't planning on going that large originally. I was going to stick with 18; some 19s look great on these cars, some don't. I'm looking at 19x11 et20 295/30/19 rears and...

Looking for a set of sn95 stainless steel 2.5" diameter flow tubes (ball/cone flange style for mid pipe connection). Preferably ones that clamp on the mufflers.

I got a good deal on a JLT RAI for and 03-04 Cobra. I confirmed with JLT that the plastic intake tube is the same as the 96-98 Cobra. It's the newer version plastic roto-molded-whatever. The question is in the PCV fittings; they're different. JLT won't provide any additional info or sell...

Not trying to start another "what springs should I buy" thread, but I need some advice. I have a convertible, but I'm looking at H&R 51652 Sport springs because of the 1.5" drop and spring rates. The convertible is not listed as compatible for for these springs, but I know they'll physically...

My OEM steering wheel is pretty chewed up so I'm looking for a replacement. After going back and forth about repairing it and keeping the airbag, I think I've decided to just get an aftermarket wheel. I think 350mm is what I want for diameter, but I can't get much in info on the grip...

I finished installing some Pypes polished stainless 3" LX tailpipes today. I think they look really good. The fit is actually pretty good too, still needs some minor tweaking on the driver's side. The pipes also do run close to the gas tank. Do you think this is a safety issue? The...

I'm trying to get this JBA H pipe (part # 6632SH) to fit my 97 Cobra. It's supposed to fit a 1996-04 GT/Cobra and it's supposed to be used with JBA's headers, which I knew in advance. So figuring I could make it work, I measured, cut the ends off, and expanded the ends to slip-fit on to the...

I'm in the middle of fabbing up this JBA o/r H pipe to fit my car. The rear O2 sensors hit the trans cross member. Since it's o/r I'm running MIL eliminators. Is there a cap I can plug into the open end of the MIL eliminator instead of the O2 sensor? Then I'd just plug the bungs in the pipe...

I'm about to order some ARH long tube headers. My car is a 97 convertible, but the part is for a 99+. I know the header should fit, but is there anything specific with a convertible I need to be aware if fitment-wise? Also the SMOG connection refers to the EGR hookup, right? Nothing else on...

For my gear install I'm going to install a speed calibration box from Abbott and it needs to be wired in. I'd like to wire it outside of the car using connectors to then plug into the VSS and transmission wire harness, instead of cutting into the harness itself. I'd like to keep the speedcal...

Which battery tender/charger do you guys recommend for garage storage? Looking for something bullet proof/tried and true that also won't burn the house down unattended. Don't really care about price, but don't want to spend more than really necessary. Thanks!

I finally got my Spintech Pro Street 6000s in stainless steel. Took about 8 weeks to get them. I think they look awesome, too bad they get hidden under the car. They're definitely a heavy duty, solid feeling, fully welded muffler. Figured I'd share some pics here since my wife isn't very...

I have the 5 piece ss slip-fit Bassani x pipe with cats and o/r flow tubes. I want to try an h pipe, but don't want to spend a fortune on a whole new ss catted h pipe (MRT is all I see available for like over $1000) and the hassle of installing it. I was thinking I could get an o/r JBA h pipe...

Anyone drive in the Dream Ride parade today? Saw some nice mustangs. There was a new edge Bullitt that had a great sounding exhaust, loud and deep, I'd love to know the setup.

This should have been straight forward, I've installed a short throw on a T45 before. This pro 5.0 though, the gold ring seems off center from the aluminum base. It's like shifted to the right slightly. I can't get a 3/8 13mm socket on the passenger side lower bolt, but driver side fits ok...