Does anyone have access to a mustang 4r70/75W and can measure the tailshaft housing length? I'm pretty sure its the shorter tailshaft housing at 10.25" but just want to confirm. Thanks.
Never got around to installing this 8 cylinder J&S Safeguard in my 03 cobra. Purchased 2 years ago. Decided to go with a Holley standalone. It is brand new in the box it came in as it was packaged. I just removed the unit from the bubble wrap for pictures. Comes with original instructions...
Selling a 2 year old Dual Aeroforce Gauge setup(swapping to Holley Terminator x). Display color is White characters. Comes with silver SVT face, original white face and silver bezel(one has more of a machined lip than the other for some reason). Also including the original pigtails for adding...
Hey guys, I have a 6 point roll bar welded in along with steeda full length subframe connectors. I plan to get stiffler's rail stiffeners, web brace, and spider brace(already have their kmember brace). I was wondering if it is still worth getting through frame subframe connectors or if the...
Hey guys, I have a 6 point roll bar welded in along with steeda full length subframe connectors. I plan to get stiffler's rail stiffeners, web brace, and spider brace(already have their kmember brace). I was wondering if it is still worth getting through frame subframe connectors or if the...
I'm trying to find a replacement of the blue fitting with 2 ports on the top of the fuel tank. I believe the smaller fitting with the single port is the vapor valve. What is the second larger fitting with the two ports called?
I have disabled my EGR via quarterhorse. However, the Catalyst montitor relies on the EGR to set. On my Cobra the EGR is bypassed and the catalyst sets no problem. What changes do I need to make to allow the Catalyst to set without depending on the EGR? Using a quarterhorse and binary editor.
I just received divisionx fuel rails and was wondering which way the frps vacuum port should face. The way the rails i received are drilled, my vacuum port would face the passenger side of the car. I'm waiting to hear back from Lethal Performance but i thought the vacuum port would face he...
Does anyone know where to get a replacement shift linkage bushing on the transmission shift arm that the shift cable connects to at the transmission? I installed a B&M hammer shifter and cannot get it into park. The adjustment is all the way at the end and acting like the shift cable is too...
I'm trying to figure out a weird issue with my front left brake. It seems like the pistons are retracting excessively when releasing the brake. The caliper also creaks when applying the brakes. I swapped to my old 03 cobra calipers(new pads and rotors) and stainless braided hoses with the...
So I ordered parts to overhaul my front end. Tie rod ends, inner tie rods, ball joints and wheel hubs.
This started out when making right turns, I hear metalic squeaking from the front left. It sounds like worn out brake pads. I checked the brakes and it seemed like the front brake wasnt...
the rear o2 sensors on my tune were previously shut down in the sct tune. I have since converted to the quarterhorse. The car is an 04 GT has cats and i have replaced all 4 oxygen sensors since they were the originals at 95k miles.
I want to make sure i turn everything back on needed to set...
I'm planning to do the jmod this weekend and was wondering what causes the check balls to go bad. The car has a trans cooler and trans fluid tends to run at 170-180 degrees. There's 95k miles on the trans and fluid/filter have been changed at least once before. I'm just wondering if I should...
I currently have a good tune with my returnless fuel system(cobra pumps feeding 4.6L 2V with 2.1KB and 60lb injectors) on my 04 GT. I plan to upgrade to a return fuel system similar to my cobra. Magnafuel 750 with an aeromotive regulator referenced for boost(1:1). I would wire the pump to a...
My 04 GT with 2.1KB was tuned 10 or so years ago with an SCT tuner. However, the rear O2 sensors are off and I would like to disable the PATS and chance fan speeds. I picked up a quarterhorse with the plan to modify my Cobra tune. I installed in in my GT instaed and when i try to exctract the...
I have an evap leak and was lucky enough to find the sourced. Its the hose between the tank and the hard line that runs to the front of the car and has white quick disconnect ends. Does anyone know the part number?
Selling a JVC KW-XG700 double din headunit with wiring to connect to a mach460 system. This is wired up to the adapters for the mach460 harness, so plug and play. It also has the double din adapter to fasten it into the dash. I am selling because I have put in a navigation unit and am...
selling my 32k mile 03 cobra front brake calipers. They were powder coated and rebuilt at 26k miles but could use a good cleaning. Pads have about 75% life left. The calipers come with stainless steel trailer pins for faster maintenance and banjo bolts. Roll pins have been added to prevent...
I'm doing some preventatitve maintenance on the GT. It was upgraded with Moser 31 spline axles and I want to replace the axle bearings and seals while i reseal the diff and change the fluid. Are the stock axles and moser 31 splines the same diameter? ie. are the axle seals and bearings the...
Does anyone know if the 2004 mustang gt has a trans temp sensor in the 4R70W. If so, is there a PID i need to add in the Torque app as I don't see it as a gauge option.
I bought back my brother's first car(2004 GT 2.1KB) as a daily to my Cobra. It has a factory remote start and has a weird issue. The car will no longer start with the key but starts just fine with the remote start. Once started, I can put the key in and drive off. I've rewired a lot of my...
Does anyone know if the accessory idlers for the inside serpentine belt(water pump, ac, power steering) are the same on an 03-04 as a regular GT? I'm talking about the tensioner idler, the one above it and the one above the water pump. I know the one above the water pump is ribbed. I saw this...