Search results

Selling my Mach 1 after many years of enjoyment. Over the past 2 years I've only driven the car a few hundred miles. I've really gotten into my Corvette and no longer have the desire to maintain/keep the Mach. Time for someone else to love the car! Here's the ad I have currently...

Not sure if this is the right sub-forum or not - so please move isn't. I'm contemplating doing a coyote 5.0 swap in my Mach. The shop that would be doing the work has done the swap before and would have all the electronics and accessories functioning as they should. As a result, all the 4.6...

I have 2 Ford GT Supercar Pumps. They were used once for a dyno session by the original owner before he opted to go with an aftermarket pickup and different pumps. I picked these up with the intention of upgrading my fuel system. Plans changed and I am no longer changing my fuel system...

mustang cobra 03 04 gt mach 1 bullit rear bumper shaved!! | eBay I've gone back and forth with this guys in eBay messages a couple of times (shown below) and he promises not to use any images of car going forward but his current ad remains... I've reported the listing as Fradulant and...

I ordered these thinking I was going to change the type of tire I used for AutoX. I ended up changing my mind and don't think I will be using these after all. They are a great looking wheel, but I don't need them. I have a set of 4, all brand new still in box. I opened each box to ensure the...

Selling my BBS RX 17x9 wheels. They were my race rims and were great! Unfortunately, I upgraded to the Brembo 2000 Cobra R calipers and these rims do not clear them without a .5-.75 inch spacer (no thanks). $850 + shipping OBO Located 33709, St. Petersburg, FL These wheels are no...

Approximately 11,000 miles. Replaced when I had the tranny out for a rebuild. 26 spline. Shop said it still has life in it but would recommend resurfacing the pressure plate. $150 + shipping OBO Bunch of pictures: 20110429 Spec 3pluse Clutch pictures by vertigyn - Photobucket

Selling my BBS RX 17x9 wheels. They were my race rims and were great! Unfortunately, I upgraded to the Brembo 2000 Cobra R calipers and these rims do not clear them without a .5-.75 inch spacer (no thanks). $850 + shipping OBO These wheels are no longer made by BBS. When they were, they...

Upgraded my calipers and rotors - selling the take offs. All parts (except for the lines, have approximately 30k miles on them - lines were put on around 15k miles ago). 2 Front PBR calipers - one has a light scratch from a wire scraping it (see pictures). Easily fixed if you paint the...

Looking to buy two of the '03/'04 Cobra wheels in the Satin/Machined finish. I have 2 and need two more for my race rubber. Shipped to St. Petersburg, FL 33709

Wasn't sure where to post this...so mods please move if there is a better place! This past week my rear coil over set up had a circlip fail causing the shock shaft to fully extend into my trunk making making the shock pretty useless. Initially I called MM to talk to them about...

Save the date - this is an awesome event! I have helped design the course and it is ALWAYS a great time! S&R Performance Poker Run! | Facebook We did an initial planning of the route this past Sunday (2/6/11) and it is going to be a great one!!! Based on the initial planning run the route...

Hey guys, what's your thoughts on the following: I bought a part recently from someone on this site. I paid the asking price PLUS the shipping that he requested ($80 for a $250 bumper) - didn't even try to negotiate him down. He was guessing on the shipping and said if it cost less, he would...

I have a Viper Spec T56, custom bellhousing to mate to Mustangs, crossmember, and a custom Aluminum driveshaft currently set up for an IRS. I have an MGW shifter for it, but it needs to be replaced as a spring and nylon sleeve are missing (we may find these pieces..but have not yet). I was told...

I know I have a Mach, but it's fairly similar to a Cobra at this point with the IRS, Viper T-56, and Kenne Bell so I thought you guys would have some good thoughts. My driveline has been annoying me pretty much since I swapped in the USED Viper T-56 and Stage 3+ clutch. It's noisy, the clutch...

I did an event back in February with this group and had a blast! Think of it as a middle ground between Autocross and Open Track events. You have instructors onsite if you want to use them and you have a whole day to do a TON of driving. I was used to doing autocross events and was VERY...

Well, why not? 04Mach1Blurr suggested it in another thread so it sounded like a good idea to me! Everyone post up to 3 of your favorite pics of your Mach =)

I just got a hold of a bare WAP aluminum block out of an '01 Cobra. I want to put it on my engine mount, but don't know what size/thread count bolt is needed. Do any of you guys know? Thanks...I know it's a stupid question, but I'm tired of searching Home Depot and buying random bolts to...

Hey guys, Just got my V1 and am wanting to hook up the direct power set up. What wire would you guys recommend for hooking the direct cable hook up into? I don't want to hurt anything and I want the power to be on whenever the car is on. The direct wire kit I'm using is the one from...

These are the catalytic converters that came with my SS Bassani modular X-pipe part # 46993 (99-04). Since I swapped to the T-56 my mid-pipe has been modified and I can no longer consider using these. They are BRAND NEW and have NEVER been used. I was told they cost $179 each from Bassani...

Like the title says a stock differential and gear and pinion out of a 2003 Cobra IRS. System worked fine when removed. Allowed one wheel to start spinning before the other causing wheel hop sometimes. It didn't do this all the time...just enough to make me want to replace it. Let me know...

For you guys that are swapping over to a turbo set up - check out my FS thread here: http://www.svtperformance.com/forums/engine-drivetrain-256/542628-fs-upper-lower-intake-manifold-off-03-mach-1-a.html Thanks!

Changed systems so selling the Steeda system. They have larger tips welded onto them and the mufflers have some dents from speed bumps. There are no leaks in the system and it sounded great when it was on the car. Asking $300 + shipping OBO. I don't have any recent pictures since I took...

Just got a KB, so the stock piece is up for sale. Has less than 19,000 miles on it. Asking $350 + shipping OBO

I'm looking into getting some Auto Meter Cobalt gauges for my newly KB'd Mach. The gauges will consist of a water temp gauge, a boost gauge, and a DPPS gauge. I'm trying to decide to get a straight boost gauge or a boost/vacuum gauge. Which one do you guys recommend and why? What's the...