I recently did the PIH swap to my 95 cobra and i looked the other day on the computer module and it said A3M1 on it instead of A9L and was wondering if they were the same thing. Any differences in them whatsoever. Any information will be helpful. Thanks
When i floor it in 1st gear and keep going thru the gears or i just floor it in 1st, the tranny feels all notchy and sometimes wont go into other gears. I can floor it in any other gear without this happening. could it just be the tranny cant take the torque i have in 1st. Does anyone else have...
I am going to get some drag radials and wanted to know if 315 drag radials are too much or I should just stick with 275 drag radials. Also what kind do u guys reccomend? Would 315's blow my rear?
I just found out that my header on my passenger side has a leak from the gasket on either cylinder 3 or 4 and was wondering how much power and how bad it hurts my 1/4 mile times? Anyone that lives in Maryland i would not reccomend going to E.L.D. performace for anything they would not take any...
Im planning on getting some wheel spacers by H&R 1 and 3/4 inches and wanted to know if they can hurt anything. Could it hurt the tire wear or make the wheel bearings go sooner. Is anybody using wheel spacers, if so can i see some pics. Thanks
Can u fit 275's in the front on a 95 cobra and do 315's have any rubbing problems. My car is lowered about 1.5 inches all around. Also do u guys have any pics of 17x9 275's and 17x10.5 315's. Any help will be useful. Thanks
I need a new transmission and was thinking about putting in a standard 3550 or a tko. Im pushing somewhere near 370-380 tq at the flywheel and was wondering if the tko would be to much or would a standard 3550 be enough. Thanks for any information.
I am having a problem with my clutch or something im not sure what exactly is wrong. When i am on a slight hill going down hill it wont go into any gear but, if i drift up a little bit then it goes right in. First i thought it was my synchros going but that wouldnt make sense if it wont go...
I am thinking about putting a infinity basslink in my car and was wondering if any one else has one or has heard one. Also where do u think would be a good place to mount it in the trunk with out causing more rattles than i already would get? Any information will be useful. Thanks A.J.
What size drag radials do u think i need? Do u think 255 on a 17x8 would be enough or should i just go with 17x9 with a 275? Any information would be helpful. Thanks
Im thinking about getting heads for my car but i cant decide which ones. The ones i have been looking at are Holleys and Edelbrock. Does any one have these heads on their cars and what kind of hp gains will i see. I was also planning to get a cam and pih. I was thinking that i would get near...
We were both going about 40mph and all of a sudden he jerked his car into 2nd gear, so i threw mine in 3rd. We both floored it and right after i hit 3600rpm i started pulling away little by little. I granny shifted into 4th and took it up to 120mph. He was still trying though he was at the...
Ive heard when you put heads or a different cam that the engine idles really bad because of the computer on it. Would the same thing happend if i threw a supercharger on it too? And which would you guys reccommend either a powerdyne or a procharger? I was thinking the powerdyne since it is...
What kind of 1/4 times are other 94-95 cobras running? The best i have run is a 14.0 and that was with a 2.3 60ft. How much hp and torque do you think im putting out? I had it dynoed before most mods and i ran 230rwhp and 270torque with exhaust only.
Mods: 1 5/8 headers (fms), phenolic...