Search results

Factory lower but aftermarket alt. I have had alignment issues with the alt due to the way it bolts up. That’s the “semi fixed alignment”. I put all new bearings in the idlers and still get a lot of wobble so I’m thinking the pulley bridge needs to be replaced.

I am currently fighting multiple really odd issues on a whipple car thats kicking my butt. It is shredding belts shortly after they are put on. There were some alignment issues that I have semi taken care of but I have an issue that is concerning. When I loosen the bolts on all of the...

Pm sent

I am selling my 2000 gt as a roller. I will do my best to list all mods. I will edit the post as I think of more things. It has 85,000 miles on the body. Suspension- Qa1 tubular k member, qa1 coilovers, upr struts, upr tubular control arms, maximum motorsports caster camber plates, upr...

What is the hp and et record for stock longblock 07-10 gt500's? I saw where evoperformance went 8s with a stock longblock. The et question was out of curiosity. But the hp question wasnt. I am trying to figure out a good hp stopping point for my car. I have an 08 gt500 motor with about 15k...

I have searched a lot and I was curious if any of you guys knew if anyone makes single turbo kits for 07-10 gt500's. I am trying to find a set of forward facing turbo headers that will fit my heads. My biggest issue is that the motor is in a 99-04 car. I have talked with cg fab and I don't...

I am thinking about going a different direction with my car. I am looking at selling my motor, turbo, and my trans. I have an 08 gt 500 motor with a modified ford gt intake with a lid, edelbrock elbow and tb. This is from throttle body to oil pan. Including everything but the fuel injectors. I...

I have an 08 gt500 motor with a 76mm turbo with a modified ford gt intake and i have a few questions that some of you more knowledgeable guys may be able to answer for me. How does intake runner length affect power and spool time of a turbo? I have been told by a few people that the basically...

I have a dynamic mighty mite c4 modular setup I want to get rid of. It is fully rollerised, billet servo, reverse manual valve body with built in t-brake, ptc 3600 stall, sfi modular bell housing, 8 bolt flex plate, and drive shaft to fit a 99-04 car. Basically everything other than the shifter...

$1200+ shipping. FIRM Kit includes: gt45 70mm turbo, waste gate is a 44mm god speed with 5lb spring, turbo xs bypass open, open down pipe, turbo xs manual controler. Note* Made to fit bullit manifold so changes will have to be made for stock plastic manifolds. A pusher fan is needed and...

Hey guys, I am wanting to learn a little about the IRS in the terminators. My main questions are how far these rear ends can go as far as a power level or et number. How built can you make them? I have only ever dealt with sra so the IRS is new to me. It would hypothetically be behind a turbo...

We are selling my wife's honda. It is a 2004 Accord V6 EX. Im pretty sure its the EX model. Its loaded. Tan heated leather, 6 disc changer, sun roof, spoiler, 17" aluminum wheels. It has recently had a new ac compressor installed and a new motherboard for the radio. These cars had a recall on...

I have a 2007 2wd Z71 Silverado LTZ that I am looking to trade. Yes, i said 2wd z71. It is an option that they had on the newer trucks. It has grey leather interior with wood grain in the console. It has a bose stereo system. 5.3 with around 79k miles. Spray in bed liner and black tool box. Has...

I know that the downfall of the termi is the heaton. I am sure you have but i dont know about it but have any of you guys figured out how to make the eaton efficient as far as heat goes? spraying meth or anything? I know e85 helps cool things down but is there anything on top of that that can...

I am looking to trade my truck if anyone has a new 5.0 car that they are wanting to get rid of for a truck. It is a 2007 2wd Z71 silverado crew cab. It has light gray interior and it is a LTZ model. It has 76k miles on it. 5.3L motor. No problems with the truck at all. I just want to get back...

Looking to trade my truck for a stang. I am REALLY wanting to get into a new 5.0 but my hopes are high on that. It is a LTZ model and has 84k miles on it. Has light gray interior and the 5.3L engine. I am not looking to trade for any bolt on cars. I am looking for an extreme street car...

I have a 2002 gt with a built motor, stock heads and intake, vt stage2 blower cams, built 4r70w, circle d 4k stall, v2sq on about 18psi. This was my first good day out at the track and was my first pass that day. It went 6.82@100mph with a 1.45 60' on foot brake and pump gas. I drove it 2 hours...

I have a set of probe srs series pistons. They are .020 bore and -18.1cc dish with about 10,000 miles on them. I also have a cobra oil pump. I need: fuel line upgrade kit, dual gt pump setup, dual fpdm or modded fpdm setup, sct ba2800 or larger, wideband, or a nitrous kit. Thanks

I am selling my complete supercharger kit. It is a vortech v2 sq s-trim with about 5k miles on rebuild, it comes with an 8 rib vortech 2.87" pulley, bracket to fit a new edge 2v, paxton 3 core front mount intercooler, all of the blower piping, vortech maxflow bypass valve, comes set up for a...

I have a vortech v2 sq s-trim, a set of .020 probe forged srs series -18.1 cc dish pistons, and a cobra oil pump that i want to trade for a T-trim or larger head unit. The s-trim has about 4k miles on rebuild. Ill throw in a 2.87 8 rib vortech pulley also

I have a 2002 mustang gt. It is redfire in color with tan leather interior. It has about 81k miles on the body, 6k on motor and supercharger rebuild, and about 10k on built transmission. Here is a basic mod list. MOTOR: Teksid block bored .020, Forged cobra crank balanced down to the gram, CP...

I have quite a few 4v parts that I have no need for and I want to sell. All of the prices are without shipping. 4v B heads and cams"assembled"- $350 4v B lower intake manifold- $75 IMRC's- $50 4v valve covers "1998 style"- $75 4v timing cover- $75 Complete 4v timing equipment including metal...

I am needing a forged cobra crank. Would like it to be in the best shape possible. Let me know what ya have with price for shipping to 39465. Needing one soon

Well, the time has come for me to do something a little different. I think I have decided that I want to build something a little more extreme than my gt. I have a 2002 mustang gt. It is redfire in color with tan leather interior. It has about 81k miles on the body, 6k on motor and supercharger...

I need some romeo heads for my 02 gt. I will also need the cam girdles that came on the heads. Would be interested in some ported heads or maybe some tfs heads if owner will take cash+parts for them...