swap

Long story short. Ive had i started the idea of building a 4v for boost about 7 years ago before life got busy. Fast forward to now, and cost for a coyote drivetrain have really went down and the support for the swap is growing faster a surprising rate. What i have now: The car is a daily...

Tons of Driveshafts just showed up over here at Lethal Performance! Everything from 11-14 GT to T56 magnum XL swap driveshafts (yes, this includes 15+ guys!). Don't see exactly what you're looking for? Have any questions? Feel free to shoot us a message or give us a call at 561.753.8105 and...

Tons of Driveshafts just showed up over here at Lethal Performance! Everything from 11-14 GT to T56 magnum XL swap driveshafts (yes, this includes 15+ guys!). Don't see exactly what you're looking for? Have any questions? Feel free to shoot us a message or give us a call at 561.753.8105 and...

Tons of Driveshafts just showed up over here at Lethal Performance! Everything from 11-14 GT to T56 magnum XL swap driveshafts (yes, this includes 15+ guys!). Don't see exactly what you're looking for? Have any questions? Feel free to shoot us a message or give us a call at 561.753.8105 and...

Tons of Driveshafts just showed up over here at Lethal Performance! Everything from 11-14 GT to T56 magnum XL swap driveshafts (yes, this includes 15+ guys!). Don't see exactly what you're looking for? Have any questions? Feel free to shoot us a message or give us a call at 561.753.8105 and...

Well... I ordered my Gen 5 3.0L Whipple back in December and it showed up at the end of March. I got it all installed and finished my tune a couple weeks ago. Here is a little bit about the set up. Car is an 01' Cobra with Terminator swap on it I completed years ago. Engine- Boss 5.0L Block...

My car is 1994 Cobra, engine from mach1 and I'm adding eaton m112 with partly selfmade swap parts (like Trilogy Motorsport set for Marauder) I'd need titles part shipped to Finland Europe, paypal in advance. I need at least the big hoses that connect to crossover. Picture from my engine

Bought this 89 notch a few years ago. It was a complete car. I got it home, drove it up the road 1/4 mile whipped a shitty came home and gutted it. It sat for a couple years. In the middle of my cobra build, I had an opportunity to buy someone out of their swap parts. Seller was from Alabama and...

Spoke to a guy today and he said that his 2850lb 05 3v made 1005hp with a novi2200 and 4r70, it ran some 9.2s I don't find that hard to believe but what if this car had to tt coyote with a 6r80. Anyone have a setup like this. 2005-09 tt coyote swap with 6r80?

Hi all! I have a black on black 98 Cobra that i'm currently restoring. The stock engine is weak so i bought an entire Mark 8 for $200 bucks! Im going to get the cobras crank checked out and get some forged rods and pistons. Also thought about a stroker, I want to leave the stock bore. Whats a...

Curious to the gains on an 11-14 coyote and any install tips. Thinking about going this route seeing how cheap they are and wanting to keep engine bay looking as factory as possible. I know you have to buy IMRC lockouts. Curious to where they go and any vacuum lines that need to be rerouted...

Located in Binghamton, NY My Cobra was Solid axle swapped by the previous owner less than a year ago. I am swapping back. I no longer need these parts, shoot me any reasonable offers on whatever you'd like, would also trade any or all for wheels/tires, or for various Terminator parts would...

So, I have finally finished swapping in my 2007 GT500 engine into my 2008 v6 shell. Upon putting the key in I had a handful of error codes, a couple were dealing with the PATS system. The red security light on the dash was blinking quickly. I cannot start the vehicle, the car wouldn't even...

Hi guys, I know this conversation and thread has been posted about before, and I read it and joined the forum for more info since you guys may have a great deal of knowledge on the subject. I have a 2008 Mustang V6 Premium Pony Package auto. I found a 2008 GT500 engine with a T6060 transmission...

I plan on swapping a 97 mkviii motor into my 96 Cobra because it started knocking.What all do I need for the swap? besides the intake. (I know it has different cams and a different crank.) any input would be greatly appreciated. the motor is from a 97 mkviii so it has the COP.

I bought a 92 LX with a 4 cylinder in it. I want to put a 5.4 DOHC out of a navigator in it. I know just about everything I need to do to the chassis, end, and other supporting mods but I need a little help on what I should do computer wise, headers and also just any issue others have ran into...

Hey guys have a brand new whipple 2.9 with 3.5 upper pulley. I have only mounted on lower manifold hasn't been installed on car or even put oil in. Should still have warranty as ive had less than a year. also selling brand new id1000 injectors Whipple 3700 shipped id 1000 850 shipped...

I have a Terminator swapped 98 and I'm having an issue. Hopefully I can post this here. Air only works in VENT and FLOOR. Every other selection kills the motor and it will not restart until turned back to OFF or to one of the working selections then keyed to complete OFF then restarted. At a...

Hey guys. I already have my 15" S77B welds on the GT500. Finally put together a video of the brake swap. It is fairly long mainly consisting of the Mustang bros working on the car. One more video is to come, swapping out the rear shocks.

Hi all, I've got a new crate engine in my 2011 Coyote. It's got the 2015 cams/Phasers/chains etc. I've been told I need to change back to 11-14 VCT for the engine to run properly. I keep getting bank 1 and 2 intake cams over retarded codes. I've heard that the S550 exhaust cams can be used...

brand new, never even threaded on asking 125 shipped

Hello everyone I need feedback on my build, I've got a teksid block bored .020 over with forged je flat top pistons, pro-seal file fit rings, Manley rods and a cobra crank with full ARP hardware in my mach 1. I also have an eaton swap from an 03 cobra I'm in the middle of installing and my...

Site is a bit confusing but I should get used to it. I have a 96 MarkVIII engine and 01 Cobra heads and intake mani, and only the eaton supercharger for now. My question is in the front end pullies do I really need all the brackets the Termi uses? Of course I need the alt. relo., but I know...

I'm currently in the process of an '86 Coupe from a 4 cylinder to a V8. I've been overseas since earlier in the year. While I've been gone, I had the car repainted. The painter extended the black stripe on the hood and I think it came out pretty good. Much better than factory. I'm hoping to...

Challenge Accepted Sam Anderson challenged himself to build a 733-horsepower classic Mustang By Steve Turner Photos courtesy of Sam Anderson If you have built more than one project car, you always want to push the next one to a higher plane than the last. That was definitely the case for...