Hey guys I have an 01 cobra and im looking to supercharge it. I am interested in buying a full eaton kit from a 03-04 cobra. I would like all the parts that come with the set up as well including intercooler. I am new to the supercharging world as I have alwas had 4cyl turbos or NA cars. Any...
I just recently swapped a 98 cobra engine in a 97 gt and am using the gt harness and computer and need a tune. I have long tube headers and CAI and full exhaust as well. What i need to kno is what kind of tune do i need, where to get it and whats the best deal i can get? Any help would be very...
So Ive had a couple threads on here about a 79 notch i'm building and a 91ish notch i ended up with for a parts car. the newer car has been swapped from efi to a carb'd setup with spray, msd, window switch and rev limiter. All of this will be placed into the 79 with the motor and tranny..i'm...
i have a 99 cobra that has a hole in the block , i also have a 02 gt motor , i need to know if i can take the top end of the cobra motor and make it work with the bottom end of my gt motor, im trying to save money and just want to get the car running again. any help with what i need to take off...
Need some help. 98gt blown head gasket bought a mark engine...need to know what all needs to be swapped for a clean install. Engine came out of a 98 mark pretty sure....and incase it came out of a 96 what am I looking at....engine came out of a automatic as well...any info appreciated...thanks
** PRICE REDUCED **
Hey guys,
Do you have a T-3650 or a TKO-500/600 that can't handle what you are throwing at it or WILL throw at it? If so, you are in luck!
Up for sale is my complete T-56 setup. Nothing wrong with it, I've just decided to go AUTO!!!!! Transmission is currently in...
Posting this to the Terminator forums because of the type of question.
I am looking into a 99 V6 Mustang for sale that has a FULL Cobra swap. Motor, trans, harness, ecu, full suspension, bumpers, grill, and seats. After this swap what other things would be different between an actual Cobra...
duratec 3.0 swap? 1997 3l work? need input..
i can get a 1997 3l duratec for a decent price, my question is what would i have to do to make it run in my 2000 contour svt, and would the 97 work? bc ive read a few posts saying that you want 02-04? all advice, answers, or help would be greatly...
Ladies and Gentlemen, here is a short summary of what i'm doing and looking for help with : Swapping a 3.8L v6:fm: w/ an 04 mach 1 4.6 and putting on an air to air intercooled vortech supercharger. I'm looking for insight on the install, suggestions or comments, tips or pointers / really...
IMAG0375.jpg picture by usmc53chief - Photobucket
IMAG0375.jpg picture by usmc53chief - Photobucket
found it at the super ford swap meet in Columbus Ohio this weekend, the back of the blower has a elbow that has been welded together to form the angle and bolted to blower and 03 throttle body
bunch of questions, prefer answers from people that have actually done the mods and cans say yes/no as far as gains and cost value. thanks
all going in a 97 mark viii 4v, but i already have a forged cobra crank, 98 cobra cams, and 97 cobra intake manifold, 03/04 cobra forged rods... so it will...
Swap near complete. Need some advice. 01 intake with throttle body, but it rubs on the 97 valve covers. Also wondering if anyone has done this, what did you do about the throttle body covering the pcv valve on the passenger side? Looking for the 01 throttle cable bracket as well. Any help...
I have nearly everything needed to complete a 03 Cobra swap.
Ported lower intake (it has a broken and rewelded mounting boss. I used it for a year on my race car with no problems)
Stock intercooler
Stock balancer
Pulley bridge
Low mileage alternator (less than 200 miles)
Front cover...
Im looking to buy a complete or at least 75% complete eaton swap kit for my 03 mach 1 with Stock 39# injectors, pumps, intercooler, MAF, 3.65 pulley, non ported eaton, etc. Let me know if you guys have a complete kit/partial kit/etc. Im looking to buy in bulk. Thanks.
Sorry it took me soo long! I had this written up and saved someone on my computer and then I completely forgot about it! I will make a separate write up that will include the complete removal of the motor, since I greatly recommend it for doing the head swap.
Parts Required:
-C-Heads...
I have a 2005 GT. Not long after I bought the car I began to envy to power capabilities of the 03/04 Cobra and GT500. The DOHC 5.4L is too expensive. I have found a lot of good deals on 03/04 engines. How hard would it be to give my S197 the heart of a Terminator?