96 cobra w/ 04 cobra motor swap fully built FS

Freaknazty

New Member
Established Member
Joined
Mar 8, 2009
Messages
20
Location
louisiana
Car is not running atm ( needs small random things to complete , few an fittings , i/c pump/tank , wiring for tb/line lock , etc. )
just installed a new b&m ratchet shifter , B&M supercooler ( large one ) , battery & battery cable (run with fuses etc. ) truth is just no time to finish it and looking to get back into other things as racing is too much a hassle for me now living so far from the track and 2 young kids . I have tons of other small random parts and things for this car too that will go with the sale ( $50 and under parts ) looking for $15k /trade+ cash title in hand & 83k on the odometer but nothing on the whole car has gone further than being rolled on and off a trailer lol . PLEASE CONTACT ME THROUGH MY EMAIL [email protected]


Motor:

04 cobra motor & harness
22k miles on the motor
ported stage IV steggy eaton
Richard Racing 2.80 upper pulley
Meziere Electric Water pump
BBK long tube Headers
MotoBlue 60 Lb. injectors
Aeromotive Return Style Fuel Rails
Metco Pulleys
Metco 4lb. crank pulley
Accufab Single blade polished throttle body
Accufab carbon fiber wrapped plenum
JLT CAI/K&N filter
SCT 2400 meter
Fluidyne heat exchanger



Transmission:

AODE
Performance automatics reverse manual valve body
P/A trans brake
FRRP deep sump pan
Abesto clutches
OD billet drum
Precision industries N/L 3200 stall (multi disk)
FRPP aluminum DS


Fuel system:

Aeromotive A1000 fuel pump NEW
Aeromotive 100 micron filter NEW
Aeromotive fuel external pressure regulator NEW
10 gallon aluminum fuel cell w/ foam insert NEW
Aeroquip stainless braided fuel line -10 (15ft) NEW
Aeroquip stainless braided fuel line -8 (20ft) NEW
Ron Davis custom 3 row aluminum radiator
sn95 electric fan


Rearend:

8.8 with tig welded axle tubes (done in jig)
Moser 33 spline axles NEW
Moser 33 spline spool NEW
Moser C-clip eliminators NEW
Ford Racing 4.56 gears NEW
Ford Racing Rear cover/girdle NEW


Steering/Suspension:

UPR Pro-Series front tubular suspension
UPR bump steer kit NEW
UPR/QA1 14" 175lb front coilovers NEW
UPR Pro-Series rear suspension w/upgraded hiems NEW
Steeda caster/camber plates NEW
Strange 10 way adj struts and shocks NEW
Welded torque boxes
Fox body rear springs
Flaming River manual rack (Sn95) NEW
Flaming River steering shaft (Sn95) NEW
Aerospace manual brake conversion (Sn95) NEW
TCI line lock/roll control NEW
Summit proportioning valve NEW


Chassis:

Wolfe 10 point Chromemoly cage (painted black gloss)
2"x2" through floor frame connectors with kickouts
Stroud window net NEW
Simpson 5 point harness BLACK (2) NEW
Corbeau Forza seats (black)
UPR air bag deletes (painted with saddle dye) NEW
Skinny Kid aluminum rear wing NEW
Weld ProStars 15x3
Moroso D2 26x4.5-15 NEW
Weld ProStars 15x10 (6.5 bs)
M/T 28x12.5 ET Streets
M/T tubes NEW
Taylor aluminum battery box NEW
Flaming River on/off switch NEW
Flaming River switch rod (for on/off through bumper) NEW
Russell stainless braided brake hoses NEW
All new hard brake lines
Repainted engine compartment and inner wheel wells






96 COBRA pictures by freaknazty - Photobucket

I also have tons more pics if needed /wanted
 

Freaknazty

New Member
Established Member
Joined
Mar 8, 2009
Messages
20
Location
louisiana
pics sent ........honestly wouldn't take much at all to finish but i can't do much of anything right now until the doctors figure out whats going on with my shoulders so it has just been sitting lately.
 

Users who are viewing this thread



Top