• Welcome to SVTPerformance!

E85 horsepower & torque list

Discussion in 'The Distillery' started by vadorsnake04, Dec 12, 2010.

  1. vjay88

    vjay88 Too little to late Established Member

    Messages:
    371
    Joined:
    Jan 20, 2008
    Location:
    Brentwood, CA

    Hopes and dreams, hopes and dreams lol Guess it helps I have a built longblock ready to go.
     
  2. 03TRKB

    03TRKB The LSX Swapped Guy Established Member

    Messages:
    355
    Joined:
    Oct 17, 2010
    Location:
    Oklahoma!
    4.6L 4V (Comp Stage 2 Blower Cams)
    M6
    18-19lbs
    636/619
     
  3. ZOSO

    ZOSO colorados baddest eaton Established Member

    Messages:
    452
    Joined:
    May 17, 2004
    Location:
    Co
    Ok finally got some numbers on my lil eaton.

    Stage2 steig ported eaton july 2004 port.
    2.8/4lb combo.
    full exhaust.
    Seeing 14psi boost.
    untouched motor
    made 530rwhp 550rwtq. On a loaded dynojet.
    Having belt slip or something cause power falls off and goes flat at 5200 rpm. This was at 26* timing and found in a data log it's too much. backed it down to 23* and will try again when I fix the power drop off problem. Gonna do plugs and a new belt as these are a few years old.

    SAE
    SCAN0067.jpg

    Uncorrected 436rwhp 453rwtq

    SCAN0068.jpg
     
    Last edited: May 1, 2011
  4. BADASS03SVT

    BADASS03SVT Well-Known Member Established Member

    Messages:
    12,989
    Joined:
    Oct 25, 2003
    Location:
    MA
    ummm.....how in the world is "uncorrected" 100hp lower? temp looks to be 65* so it should have been close if not a bit higher. "Uncorrected" is what the car actually made....SAE corrects it to 77 degree's
     
  5. Shadow Grey 03

    Shadow Grey 03 Well-Known Member Established Member

    Messages:
    5,797
    Joined:
    Nov 24, 2007
    Location:
    Hilliard, Ohio
    I'd assume it's based on the altitude. I think it shows something like 7100 or so.
     
  6. BADASS03SVT

    BADASS03SVT Well-Known Member Established Member

    Messages:
    12,989
    Joined:
    Oct 25, 2003
    Location:
    MA
    d'oh...didn't even notice that....way to go me...:bash:
     
  7. ZOSO

    ZOSO colorados baddest eaton Established Member

    Messages:
    452
    Joined:
    May 17, 2004
    Location:
    Co
    Yep way up here at a mile high. No air to make power.
     
  8. yfzkevin

    yfzkevin Member Established Member

    Messages:
    271
    Joined:
    Oct 13, 2009
    Location:
    Oceanside, ca
    806rwhp and 821rwtq @5800 rpms and 19* timing and 23~24psi

    Gonna add more boost and rpms and timing and get rid of the belt slip and see where she is at then. Stock heads and cams. Built short block, whipple 3.4 crusher, 5.0L stroker, 105lb injectors
     
    richie_1 likes this.
  9. dlaude

    dlaude Active Member Established Member

    Messages:
    522
    Joined:
    Mar 23, 2009
    Location:
    New Lenox, IL
    486/495...only a 2.76, mid-pipe, catback, and jlt cai
     
  10. kleistang

    kleistang Member Established Member

    Messages:
    404
    Joined:
    May 12, 2009
    Location:
    Miami
    23-24 on a 3.4 is that under spinning the blower ? that think should be sick at 26+
     
  11. SVT03Chris

    SVT03Chris NASM Personal Trainer Established Member

    Messages:
    8,140
    Joined:
    Jan 31, 2008
    Location:
    Tulsa/Norman, Ok
    Pretty sure it is pullied for a lot more, but belt was slipping and made around 23-24psi.
     
  12. mtnrunner

    mtnrunner New Member Established Member

    Messages:
    74
    Joined:
    Oct 12, 2009
    Location:
    Oceanside
    ^^Yup we are trying to boost right around 30psi but the whipple upper pulley and stock tensioner could not hang. A Reichard racing setup will be going on the car soon and hopefully stop belt slip and get the boost and timing up.
     
  13. stkjock

    stkjock Corn Powered 900 HP! Established Member

    Messages:
    5,103
    Joined:
    Jan 25, 2010
    Location:
    NY
    take a look at the thump racing tensioner, it's a kick ass pc
     
  14. sickass50

    sickass50 Member Established Member

    Messages:
    292
    Joined:
    May 14, 2004
    Location:
    Florida
    1033hp/856tq on E85
     
  15. gt347mustang

    gt347mustang Well-Known Member Established Member

    Messages:
    2,294
    Joined:
    Jun 29, 2006
    Location:
    Colorado
    whats your setup?
     
  16. stkjock

    stkjock Corn Powered 900 HP! Established Member

    Messages:
    5,103
    Joined:
    Jan 25, 2010
    Location:
    NY
    looks like there is a new #1
     
  17. sickass50

    sickass50 Member Established Member

    Messages:
    292
    Joined:
    May 14, 2004
    Location:
    Florida
    twin 67s
    5.1L Stroker
    Stock Heads
    Custom Cams
    sullivan intake
    E85 and 27 psi
    I had a bunch of exhaust leaks and this was in a 97 degree shop. I'll be putting it back on the dyno in the next couple weeks and will have better #'s
     
    richie_1 likes this.
  18. paulsauto

    paulsauto Member Established Member

    Messages:
    148
    Joined:
    Nov 7, 2009
    Location:
    oglethorpe, ga
    fox vert 5.4 4v twin 67's corn fed 900rwhp @ 23psi more to come
     
  19. Blow-By Racing

    Blow-By Racing Member Established Member

    Messages:
    66
    Joined:
    Feb 17, 2005
    Location:
    Boca Raton, FL
    BBR Built 4.6 3V 302 Stroker
    BBR Stg 3 CNC Heads
    BBR Stg 2 Camshafts
    Kenne Bell 2.8H on 18-19 psi
    ARH LT Headers
    80 lb Injectors
    BBR NEW Fuel System
    94 degree shop air temps

    ** Ran out of injector **
    ***updated graph coming at end of the week***
     
    Last edited: Jul 5, 2011
  20. GodStang

    GodStang Well-Known Member Established Member

    Messages:
    14,293
    Joined:
    Aug 20, 2003
    Location:
    Aiken, SC
    What injector you going with now? After the 80s?
     

Share This Page