Post the little touches...

[Lambeau]

Remote Keypad / Actuator
Ford P/N KB3Z-14A626-A 1X
For a 2020 Mustang it must be programmed by dealership.
Its a sealed unit, that has no access to the battery.

Attached by double-sticky backed tape (already applied).
I raised it slightly to allow water to flow below.

 

[mysticsvt]

That's

Remote Keypad / Actuator
Ford P/N KB3Z-14A626-A 1X
For a 2020 Mustang it must be programmed by dealership.
Its a sealed unit, that has no access to the battery.

View attachment 1646812

View attachment 1646813

Attached by double-sticky backed tape (already applied).
I raised it slightly to allow water to flow below.

View attachment 1646815

That's pretty cool! I have a friend that put one in his side window louver.

 

[Lambeau]

Diode Dynamics LED Smoked Sidemarker Lights
P/N: SMLED3
Installed on 2020 Mustang GT
Made in USA!
Simple installation, fit was perfect

New & OEM

Also used dielectric grease on the connections.

OEM

NEW

OEM

NEW

 

[Lambeau]

JLT Oil Separator Model 3.0
P/N: 3024P-B
Made in USA!
Simple installation. Instructions direct you to remove strut tower brace and intake cover.
Good idea, but I was able to do it without removing either.

OEM part & JLT 3.0 Oil Separator

OEM

JLT Oil Separator installed

 

[Lambeau]

Steeda Jacking Rails for 2020 Mustang GT Convertible
P/N: 555-5207
Made in USA!
Simple installation, remove/replace 8 fasteners.
These jacking rails will make it very easy to raise the car for oil changes/maintenance.
Be sure to have some Blue Loctite on hand.
It wasn't listed in any of the videos or instructions I've read, but it was applied to
the OEM bolts I removed.

OEM Bolts prior to installation

OEM bolt (top) appears to be cadmium coated and had blue Loctite applied.
Steeda bolts look to like zinc/chromate.

So instead of using the shorter chromate fasteners that were supplied,
I reapplied Loctite and reused the OEM fasteners in the front.

Passenger side pic front to back:

Driver side pic front to back:

Jacking points on the rear of this GT convertible are difficult to find.
The 2 jacking points in the rear are obstructed by square structural members.
Another reason to install the jacking rails.

The Jacking Rails extend about 1/4" below the pinch welds.
Definitely need to use a rubber pad on the jack!

EDIT 7/13/21:
I actually went back and changed out the rear steel/chromated bolts with ones made from stainless since they were visible.

 

[Lambeau]

lol

 

[Lambeau]

Just changed oil for the first time at 1,062 miles and installed the
Ronin Factory Ford Easy Oil Drain on my 2020 Mustang GT:
($80, Made in USA, USA Owned Company, Veteran Supported)

FORD EASY OIL DRAIN

OEM drain plug I replaced:

Ford Easy Drain Plug installed. To use the Drain Plug, unscrew and
remove the gold cap. Screw-in the Adapter (in my hand).
The farther you screw it in, the more it opens the valve, and the
larger the volume of oil comes out.

 

[Turkey_Lurker03]

Spray painted ugly rusty driveshaft, cut up old mbrp cat back I had, installed borla XR-1 and then ran it out the side on my 13 FX4.

Sent from my SM-G965U using the svtperformance.com mobile app

 

[Lambeau]

Just changed oil for the first time at 1,062 miles and installed the
Ronin Factory Ford Easy Oil Drain on my 2020 Mustang GT:
($80, Made in USA, USA Owned Company, Veteran Supported)

FORD EASY OIL DRAIN

OEM drain plug I replaced:
View attachment 1647753

Ford Easy Drain Plug installed. To use the Drain Plug, unscrew and
remove the gold cap. Screw-in the Adapter (in my hand).
The farther you screw it in, the more it opens the valve, and the
larger the volume of oil comes out.
View attachment 1647754

View attachment 1647751

Changed oil the other day prior to storage, 2,900 miles. The drain pan I have will only fit 6 quarts comfortably and this valve works really slick to meter out ~5 at a time!

 

[03cobra#694]

I've always liked this thread.

 

[03Sssnake]

 

[BOOGIE MAN]

View attachment 1673222

Funniest license plate frame I ever saw was on an unmarked charger, said "Smile, I could be behind you instead"

Posts and likes are not mine.

 

[Lambeau]

Installed Strut Tower Covers, Running Pony, version 2, made by Custom Pony. I'll get them primed/painted with a rattle cans ordered from Automotive Touch-up.
BEFORE:

AFTER:

 

[olympic]

Had some extra 3M carbon fiber wrap left so I threw it on my F150 key chain.

 

[1 Alibi 2]

3X C/F tank cover, ( Trufiber ), not listed on their site yet ( 09/30/2021 )
I got this prototype back on 05/11/2021..
.

 

[BlksvtCobra01]

I got these for my wife’s 2015, I believe @Lambeau posted these up.

OE

LED


Sent from my iPhone using Tapatalk

 

[Lgc85]

Painted center caps

 

[Lgc85]

Mystichrome to match the seats.

 

[CobraBob]

I got these for my wife’s 2015, I believe @Lambeau posted these up.

OE

LED


Sent from my iPhone using Tapatalk

Big difference. LEDs are so superior. Nice mod, sir!

 

[CobraBob]

Painted center caps View attachment 1731818

I almost missed commenting on that mod. It's very subtle, but nice. I like that it matches the body paint.