Quest for low 11's

[Peter]

I have some pics of my Cobra with welds and battery
relocated, looking for lower ET's!

Pete:burnout:

 

[Peter]

I'll try again.....

 

[Peter]

Again...

 

[NoRcAl CoBrA]

i am shooting for high 11s on drs new motor shold be here in 2 weeks i am all motor though good luck post ur time maybe even a video

 

[SNCBOOM]

Best of luck with your new set up :thumbsup: can't wait to see some video of the beast going down the track

 

[Peter]

I was looking to go to the track tomorrow,but it's
been raining here for about 6 days and it don't
look good for Memorial Day. It's a bummer!

Pete.

 

[NoRcAl CoBrA]

man that sucks its like 85 out here in cali

 

[Peter]

Originally posted by NoRcAl CoBrA
man that sucks its like 85 out here in cali

Rub it in why don't ya!


Pete:thumbsup:

 

[Peter]

Norcal Cobra-
Where did you get yor new motor from?
Any upgrades?

Pete

 

[NoRcAl CoBrA]

stock long block Lts, 4:30,kn fipk no headlight and air filter when i am on the track one griggs race seat worn ass suspension so she hooks good shortened runners timing adjuster off road x 2 chamber flows \
oh did i mention it is freakin gutted to death just carpet dash with no ac or radio an one seat

 

[Peter]

I thought shortened runners worked for
superchargers.

Pete.

 

[Poiznus]

Looks good Pete! Let us know what happens.

Also, how is your fuel system setup? FMU? MassFlow? Pound injectors? I need to upgrade my fuel setup......

 

[NoRcAl CoBrA]

aeromotive for me

 

[Peter]

Poiznus- I use a 255 in tank with the Vortech aux.
pump stock rails feed Motorsport 42lbs with a
4:1 FMU. I might ditch the FMU, but I would need to
reprogram my chip. On my last dyno she ran about
10:1 A/F ratio(very fat), but safe. I use an 80mm Proflow
with an Andersen power pipe.


Pete:thumbsup:

 

[Alex_96Cobra]

Sweet setup. Let us know what you run!

A

 

[97SVTStang]

Hey what size are your rims up front? I have a set of Weld Draglite with M/T ET Streets for my rear. What size you have on the front I skinny ones to match my rear but I dont know the back spacing for the front.

 

[Peter]

Originally posted by 97SVTStang
Hey what size are your rims up front? I have a set of Weld Draglite with M/T ET Streets for my rear. What size you have on the front I skinny ones to match my rear but I dont know the back spacing for the front.

Those are 15X4, but a little secret they will no fit
with cobra rotors so I am using gt rotors for
now. The car hooks great even on the street!

Pete

 

[Peter]

97svtstang- Do you have the weld xp's?

Pete

 

[Poiznus]

Originally posted by Peter
Poiznus- I use a 255 in tank with the Vortech aux.
pump stock rails feed Motorsport 42lbs with a
4:1 FMU. I might ditch the FMU, but I would need to
reprogram my chip. On my last dyno she ran about
10:1 A/F ratio(very fat), but safe. I use an 80mm Proflow
with an Andersen power pipe.


Pete:thumbsup:

Thanks for the info Pete. I have about half of that done already. Just need to figure out what to do with the FMU. :beer:

 

[NoRcAl CoBrA]

I WANT HIGH 11'S ALL MOTOR BEFORE I PUT ON 12# ON MY TURBO THAT SANTA IS BRINGING ME