• Welcome to SVTPerformance!

Terminated Mach 1 Results

Discussion in 'Time Slip Bar' started by SS EATR, Apr 7, 2019.

  1. SS EATR

    SS EATR Member Established Member

    Messages:
    894
    Joined:
    Feb 22, 2011
    Location:
    La Crosse VA
    I got to test out my winter build at the track a couple weeks back. I blew a headgasket at the end of last year so I also upgraded to a set of custom blower cams with springs. I have a 03 Mach 1 that has been terminator swapped, and the car made 629/554 to the wheels through the 4r70w. Im running around 20 PSI on a 2.3 VMP blower with a 110/93 fuel mix. Here are the results from the 1/4 mile run, going to make a few more changes and get the tune dialed in a bit better and hopefully see mid 9s.

    986_zpslobovkfc.jpg
     
    tvspower, me32, 11Sec_Lx and 2 others like this.
  2. P49Y-CY

    P49Y-CY selfie deaths ftw Established Member

    Messages:
    10,233
    Joined:
    Jun 21, 2003
    Location:
    south oc, cali
    Nice! Irs or sra, and what tire?
     
    SS EATR likes this.
  3. SS EATR

    SS EATR Member Established Member

    Messages:
    894
    Joined:
    Feb 22, 2011
    Location:
    La Crosse VA
    It's a SRA with 3.73 gears, and a Mickey Thompson 275/60/15 ET Street R
     
    tvspower, MG0h3 and P49Y-CY like this.
  4. blownstang4.6

    blownstang4.6 Active Member Established Member

    Messages:
    413
    Joined:
    Nov 8, 2011
    Location:
    Chicago
    Awesome! Mine makes 508/436 on the stock motor with a Vortech through a 4r75w. Should go 10.90's at full weight once I get a chance to run it. Ran 11.37 a few years back when it made 452/386. Once I forge the motor and give it a little more timing on E85 I'm looking to be high 9's. Have a cobra shortblock laying around to use, but will ditch the low compression pistons for some in 10.5-11.0 range. Stock heads/cams, Vortech V1 S at 14psi and about 18-19 degrees of timing should make around 660. Fuel system on E85 will be maxed about there and I'm not pushing it any further.
     
    SS EATR likes this.
  5. me32

    me32 BEASTLY SHELBY GT500 TVS Moderator

    Messages:
    12,776
    Joined:
    Sep 6, 2005
    Location:
    CA,NorCal
    Great job. Its fast
     
    SS EATR likes this.
  6. BlckBox04

    BlckBox04 I am the liquor Established Member

    Messages:
    4,864
    Joined:
    Dec 24, 2007
    Location:
    NJ
    60' was money. That's what got you that 9
     
    SS EATR likes this.
  7. SS EATR

    SS EATR Member Established Member

    Messages:
    894
    Joined:
    Feb 22, 2011
    Location:
    La Crosse VA
    Yup, car has always had a good 60ft though, even with a ported eaton it was 1.5xs. Im adding some 4.10s soon to try to see a 1.2x 60ft
     
  8. BlckBox04

    BlckBox04 I am the liquor Established Member

    Messages:
    4,864
    Joined:
    Dec 24, 2007
    Location:
    NJ
    what rpm are you running through the trap at?
     
  9. gimmie11s

    gimmie11s Handlebar mustaches... PSSHHH! Established Member Established Member

    Messages:
    9,238
    Joined:
    Jun 1, 2004
    Location:
    so cal
    Impressive!!
     
    SS EATR likes this.
  10. SS EATR

    SS EATR Member Established Member

    Messages:
    894
    Joined:
    Feb 22, 2011
    Location:
    La Crosse VA
    I'd have to look at my datalogs but I'm thinking around 6k. According to a gear calculator I used I'll be able to run 145mph with the 4.10s though so ill be good for a while
     
  11. BlckBox04

    BlckBox04 I am the liquor Established Member

    Messages:
    4,864
    Joined:
    Dec 24, 2007
    Location:
    NJ
    yea you don't want to go through all that work swapping gears and then find out you're out of gear at 1000' mark
     
  12. SS EATR

    SS EATR Member Established Member

    Messages:
    894
    Joined:
    Feb 22, 2011
    Location:
    La Crosse VA
    Oh yeah that would suck lol. I'm going to double check before putting them in to be safe, but i'm pretty sure I'll be fine.
     
  13. blownstang4.6

    blownstang4.6 Active Member Established Member

    Messages:
    413
    Joined:
    Nov 8, 2011
    Location:
    Chicago
    What converter do you have in it?
     
  14. SS EATR

    SS EATR Member Established Member

    Messages:
    894
    Joined:
    Feb 22, 2011
    Location:
    La Crosse VA
    Just a cheap PTC 3400
     
  15. CobraBob

    CobraBob Authorized Vendor Premium Member Established Member

    Messages:
    88,765
    Joined:
    Nov 17, 2002
    Location:
    Cheshire, CT
    Definitely very impressive performance. Nice mods. Your Mach, I mean TERMINATED Mach, is freaking beast!
     
    SS EATR likes this.
  16. SS EATR

    SS EATR Member Established Member

    Messages:
    894
    Joined:
    Feb 22, 2011
    Location:
    La Crosse VA
    I appreciate it! All the work this past winter was worth it
     
  17. persico

    persico Member Established Member

    Messages:
    58
    Joined:
    Sep 18, 2018
    Location:
    Buffalo, NY
    Noice!!!!
     
  18. CobraBob

    CobraBob Authorized Vendor Premium Member Established Member

    Messages:
    88,765
    Joined:
    Nov 17, 2002
    Location:
    Cheshire, CT
    Now go eat some SSs. Dinner time.
    upload_2019-4-21_22-10-14.png
     
  19. 11Sec_Lx

    11Sec_Lx Well-Known Member Established Member

    Messages:
    2,811
    Joined:
    May 31, 2003
    Location:
    Indianapolis
    Nice job!
     
  20. Frankyv14

    Frankyv14 New Member

    Messages:
    1
    Joined:
    Oct 3, 2019
    Location:
    Paris
    It's a big project, I just hope you can bring it to fruition.
     

Share This Page