I am purchasing an air fuel wide band gauge from speed hut, however I'm not sure which controller I should have the gauge compatible with. Looks like the offer aem and a few others. Any thoughts? Help appreciated.
Looking for a 1.125 bore brake master cylinder for my 97 cobra. I know wildwood makes a unit but was looking for something that looks more stock. Any suggestions?
Like the title says. More up for grabs than posted but here are a few so far. Came out of a 97 mark 8 motor with 90k miles. Was still running before tear down.
stock rods and pistons $125 shipped
cop covers $50
Also have valve covers as well $75
Everything listed is plus shipping...
Just bought a Lincoln mark 8 motor to rebuild for my cobra and am looking for good info on proper teardown. My main objective is to get down to a bare block that I can send out to be cleaned. Looking for a good resource that has pretty well drawn out steps. Any suggestions? Saw a few books...
Like the title says. Looking to see if someone can help me out with pictures of the decals on the underside of the stock hood on a 96-98 cobra. Had mine repainted a while back and never replaced the stock stickers. Any help would be appreciated!
Like the title says. Looking for oem floor mats. My drivers mat has a nice heel hole in it. Looking for the stock kind without the logo, but also possibly interested in the upgraded cobra logo mats. PM is best.
Looking for some advice. Car is a 97 cobra with a stock motor other than imrc deletes. Under acceleration, car hesitates and bucks. Fuel injectors are 2 years old, and using the screwdriver and stethoscope method i heard them all click. Fuel filter was replaced at the same time 2 years ago...
So i’ve been in the process of doing a cts-v brembo conversion front and back on my 97 cobra and have questions about hard line fittings. I believe i bought 2 sizes ( 7/16 and 3/8) or something like that. Just realized i have a 7/16th on the drivers and a 3/8th on the passenger...is that...
Like the title says. Brand new maximum motorsports front control arms. Were installed and car was never driven. 0 miles on them. May show very very minor wear from installation. Fox length to help better tuck the front wheels.
$250 plus shipping. Pm is the best qay to contact.
Hello all,
Have a complete coil over kit for my sn95 cobra. So far i bought the 12 inch 400 front coil springs for the front but am having a hard time figuring out what to do on the solid rear axel. Lots of info about irs rates but not sra. Shocks and struts are koni yellows sports. Thanks in...
having a hard time finding what’s going on with my 97 cobra and looking for help. The main problem with the car is if i start in too low a gear, the car will buck on and off uncontrollably. Under a correct gear it’s not as bad and as the rpm rises it gets better. Only happens under load ( so...
looking for driveshaft recommendations. Car started off skipping at a low rpm if i was in too high of a gear but now skips and vibrates throughout the gears. Believe it to be a driveshaft. Looked at the ford racing ones but are there stronger shafts for a little more money? Dont see any that say...
like the title says. Looking for a used 14 inch front rotor from a gt500. Just using it to mock something up so as long as it’s not too bent or broken it doesn’t matter. Pm me if you have one.
like the title says. I assume 94-04 front spindles are all the same but i may be wrong. Looking for a 5 lug front spindle (passenger or driver side). Would be going on a 97 cobra. Pm me what you have.
looking for mm k member and standard offset control arms as well as a coil over kit for koni yellows. Pm me what you got. Theyll be going on an sn95 cobra.
After searching the internet for anyone else who did this, the only thing i could come up with was a few people who put front seats in but couldn’t find anything on the rear seats. I figured it was possible so i bought a pair and went for it. honestly it fits almost like it was made for the car...
Like the title says. Looking for front and rear black leather seats from a 15 or newer GT. Looking to upgrade the outdated seats in my SN95 cobra. PM me what you have.
So my last thread was taken down because i guess i broke some rules so here's a new one. I bought a rear swaybar from STEEDA 3-4 years ago..."the last sway bar you'll ever have to buy". Well it broke a few days ago. I called Steeda and i guess the one i have wasn't a lifetime warranty one so...
like the title says i need this asap. Looking for stock replacement look carbon fiber front fenders, hood, and bumper. Looking to paint them the normal color of the car...ANY ONE KNOW OF ANY PLACES? i just hit my pride and joy at 5mph and it folded like a bitch, im devastated.
I know this may seem very odd. I have a 99 mercury mountaineer beater daily driver that has the stock 5.0 with 140xxx miles on it. I recently came across a nice 6.2 50k mile GTO engine from a very much totaled GTO. My questions is this...will my automatic transmission from the mountaineer...