I know this subject has been gone over before but my specific questions are:
on a 2007 GT500 with H&R race springs and a BMR adjustable panhard bar will a 10.5 inch 20 wheel with a 45 offset fit in the rear fender without any modification?
I want t put a 315/30/20 toyo R888 on but I need...
I am looking to get new wheels for my 2007 GT500 in torch red.
I want to stick with 18's as i just bought tires 1,500 miles ago.
I am leaning towards chrome or silver, but very limited in 18's. thinking of forgestar F14's in silver but have not seen any pics.
post up any pics with...
Have a red 07 GT500 and want to know what is the best wax for a flat paint.
I do not want to do the porter cable route and want no white residue to dust off.
car was clayed a few months ago and used mazerna wax, just dont want another 8 hour waxing session!
I put an MRT O/R H pipe on my 2007 GT500 with the Bassani Race axle back.
The sound is raspy and very loud, i want to change the axle back but what one will make it sound deeper and not as raspy.
I have always had magnaflow on previous mustangs wnd liked the sound, but heard the fit was...
I have a buyer for my 03 anniversary cobra. I am thinking about getting an 07 GT500 with about the same miles (17,000) and with just a little more power, 550 for the GT500 and 525 for the cobra.
If anybody has done this, are there regrets or was it a good change?
re-port or 2.8 kenne bell
I had my eaton ported with a Stiegemeier stage 5 port about 9 months ago.
I have put approx. 2,200 miles on it since and last week it started making this whistling sound. My tuner took it off and found that the welds in the plate broke and the plate was loose...
S&R Performance in Tampa holds an annual poker run.
this year it is on 2/27/11 @0830 and is about 180 miles of twisty turny back roads in pasco and hernando counties.
There usually is alot of european and ricers with a few domestics, inclouding about 10 stangs. we are trying to bump up...
i am looking to trade my 2003 silver anniversary edition with 16,700 miles
for a 2008 to 2010 GT500 plus cash. I have the title and it is in perfect shape with no dings dents or scratches.
The following is a list of mods:
Steggy stage 5 ported blower
Ported dragon plenum
6lb metco...
I ordered some brembro rotors and did not like the drilled look. So, not I am contemplating Baer or DBA with hawk HP+ pads.
I am thinking about the two piece Baer or the one piece DBA 4000 series. The 2 piece DBA seem expensive and overkill for street and occassional autocross.
Any...
I see that Stainless steel systems and Stailess steel works both make polished catbacks. Any body have them for the terminator? i am looking for new, want polished to save time from polishing others i thought i would get one of these systems. or i could buy the bassani as it seems to be the...
i have stock headers, O/R prochamber and currently magnaflow catback. It sounds good when wide open but i rarely drive it and want to get a little louder. i also want to polish the new one and do not like the weld on the SLP so thought of stingers or bassani. i also think the magnapacks pop to...
I just bought NT05 rears in 315/35/17 and mounted them on 10.5/17 rims.
the tire rubs the bolt on the sway bar. the end of my stock studs have 1/4 inch on the end of them with no threads. I have 1/4 inch spacers which seem to clear the bolt but the lugs wont go on. so what length studs do...
I have a steggi stage V ported throttle body and eaton and a 2.8 upper, a SCT tune and no other supporting mods, which dynoed at 510/477. I want to change the pulley set up to get more torqe. Do i just need to add a 4# lower, or do i need the idler set, tensioner, etc. I would like to get all...
I have a 03 silver anniversary edition for sale with 13,300 miles. Mods are as follows:
2.80 upper pulley
single blade throttle body
JLT ram air intake
H&R race springs
C/C plates
AFCO pro series heat exchanger
O/R prochamber
Magnaflow exhaust
MGW orange handle shifter
LMR deep dish...
I am thinking about changing the wheels on my silver 10th anniversary terminator. I want to keep the original look, so anybody have pics with the deep dish replicas from Late model restoration.
Any other ideas and pics would be great. I want to keep 17's