Undecided on Stance

Revvv

Infinity Poster
Established Member
Joined
Dec 8, 2017
Messages
10,189
Location
GA
I'm not sure whether or not I like what I have created. I am running FRPP C springs and Steeda ball joints without the spacers. I wanted a slight rake, but...

Opinions.
20180412_094908.jpg
20180412_094917.jpg


Sent from my [device_name] using the svtperformance.com mobile app
 

PaxtonShelby

iamdrab
Established Member
Joined
Nov 16, 2010
Messages
5,434
Location
Pittsburgh, PA
Sorry to bust your balls Revvv but Wow that’s a bad pic!

It looks sunny outside. Run out there and snap a pic...or open the dang family room window. :)

I tend to like less rake on cars unless they’re from the 60’s-70’s.
 

Revvv

Infinity Poster
Established Member
Joined
Dec 8, 2017
Messages
10,189
Location
GA
Sorry to bust your balls Revvv but Wow that’s a bad pic!

It looks sunny outside. Run out there and snap a pic...or open the dang family room window. :)

I tend to like less rake on cars unless they’re from the 60’s-70’s.
I was inside a store in my little town. The reflections are nasty.

I had time to waste, so I took a pic when I saw the car through the window.

The car is filthy at the moment. Between thunderstorms and pollen, I can't keep it clean.

I will try to give the car a bath this evening and take a few better pics.

As for going lower than C springs; I have a million speed bumps and humps to go over. I am already touching the midpipe on some speed bumps.

Sent from my [device_name] using the svtperformance.com mobile app
 

98 svt

Well-Known Member
Established Member
Premium Member
Joined
May 16, 2005
Messages
24,008
Location
Massachoooosetts
As for going lower than C springs; I have a million speed bumps and humps to go over. I am already touching the midpipe on some speed bumps.

Sent from my [device_name] using the svtperformance.com mobile app



So you want to create the rake by raising the back?
Or are you saying it's too low up front? I can't tell in those pics. If it's too low up front, add the Steeda spacers.
 

Revvv

Infinity Poster
Established Member
Joined
Dec 8, 2017
Messages
10,189
Location
GA
Ok, I had to stop for gas. Here a a pic of my filthy little GT.

No, the chin is not as high as it appears. It's an optical illusion due to the immediate slope in the parking lot.
20180412_151646.jpg


Sent from my [device_name] using the svtperformance.com mobile app
 

Smooth

Well Seasoned
Established Member
Joined
Jul 21, 2009
Messages
10,519
Location
Wisconsin
It doesn't look bad preacher bud. I'd like to see it on a level surface without that drop from the concrete area.
 

Revvv

Infinity Poster
Established Member
Joined
Dec 8, 2017
Messages
10,189
Location
GA
I've considered 18s when I eventually do wheels. I will keep a stock diameter tire and stagger the widths. I am almost certain I want a 10.5" rear wheel.

Sent from my [device_name] using the svtperformance.com mobile app
 

Revvv

Infinity Poster
Established Member
Joined
Dec 8, 2017
Messages
10,189
Location
GA
As promised. I still suck as a photographer though. Then again, I didn't really slow down or stop to take a good pic.

Here is the GT on FRPP C springs, with Steeda ball joints (spacers used).

The OEM wheels and tires do not do this car any justice.
20180501_115548.jpg
20180501_115809.jpg


Sent from my [device_name] using the svtperformance.com mobile app
 

Users who are viewing this thread



Top