Recent content by 01slo vert

So, its been a while since I've been on here but i have some questions. I've been doing some research on coil overs for all four corners and from what I've come up with is that MM, Griggs and KW are the top three companies to deal with. Now my question is, is one company "better" than the other...

These brackets are brand new. Got them with the seats and do not need them. Looking to get $150 shipped or trade for Corbeau brackets for an 01 Cobra. Best way to contact me is call/text. Thanks Steve 8456299762 Only have pictures of the passenger one because the drivers is still connected...

Have all four in very good shape with minor rash on one wheel. they have tires on them but there about 4/32" left on them. asking $500 but make any reasonable offer. i really need them gone. Thanks, Steve Best way to get a hold of me is to call or text 8456299762

like title states have a full set of 2001 Cobra seats for sale. they are not perfect and I really need them gone. asking $600 but make me an offer. I really need these gone. Thanks, Steve best way to get a hold of me is to call or text 8456299762

Ok so I finally got time to start assembling my motor and I ran into a little snag. I have the ARP Main Studs and it seems that the two smaller, outter studs are too short. I called ARP and explained what was going on and they stated that since its an aluminum block they would just remove the...

Like title states, I have a Craftsman Tool box, top & bottom forsale. Cost around $1800 new years back and is still in like new condition. Only thing wrong with it is that the top draw on the bottom back has a bent slider. Draw only opens about half way but closes all the way. Looking to get...

Well I'm sending my heads out next for my motor (5.0 Stroker) and in the process I found a 93 Mark VIII motor and trans (auto 4R70W) for real cheap. I'm thinking about picking it up and using the motor and selling the trans. I want to put the motor in my car to be able to somewhat enjoy it until...

I have a full Stock 01 Cobra rotating assembly forsale. The crank was completely resurfaced and the pistons and rods were cleaned up. I have all necessary bearings and have new rings still in the box. I will post pictures up later. I also have new 5.0 stroker bearings in the box for sale too...

Like the title states, up for sale today is a White 2001 Cobra Convertible with a Vortec Supercharger on it. The car is a guy I work with, wifes car. It has 48,8.. miles on it and has rarely been driven the past few years. It was purchased from the original original owner with very little miles...

I'm looking for the engine removal write up. I've been searching for a good hour now and have had no luck other then people talking about it. I'm pulling the motor and trans out of my car this weekend and am going to be doing it in the driveway. I have ramps and a backhoe with chains at my...

Well a couple days ago i finally decided to bite the bullet and order some parts. :banana: I ended up going with the 5.0 Stroker rotating assembly from MMR. I went with 10:1 compression, .020" over pistons with the valve relief cuts in them and ordered there street/strip oil pump. They said its...

I'm still in the process of looking for the right motor for my car, doing research day in and day out. I found a company (Stage 3 Motorsports) that has a 5.1 Stroker shortblock forsale. Just seeing if anyone has ever delt with Stage 3 before and if they have any input. Below is the page of the...

long story short, i have a 2001 cobra with a rod knock and may have found an 04 motor and trans. ive been doing some research to make the motor and trans work in my car and am curious to see what everyone has to say and looking for some input. heres what ive come up with so far to get everything...

on my way to work not too long ago, i was driving on the highway and see a real clean Audi B6 S4. i pulled up along side of him and start chatting turns out hes all stock, like me, just no cats. we did a pull from 50 at first and after the third honk, i pulled out half a car and held it till 130...

i have a 2001 Cobra and am rebuilding the motor... trans is coming shortly after. im not sure yet as too if i want to go with the MMR 4.6L kit(400900RA) or the 5.0L stroker kit (400900SRA). i want to get some outside opinions on there products and some power numbers people got with both the 4.6...