Recent content by JGEMNTL

hey guys, just installed my line lock. was thinking of putting switch where the coin holder is ? what is your opinion ? where did you guys put yours, any pics ?

i keep being told go aluminum it will save me 15 to 20 hp, but the more i look, i see most guys running the steel flywheel ? why ? anything else i need but spec 3+, flywheel, 26 spline and throw out bearing ? am i missing anything or any suggestions ????

ok, last year i sent out my supercharger to steggy, got a stage 5 port, polish, changed all pullys 2.76 upper # 3 lower. i also put in the adj. clutch cable. i have put probly 3,000 miles on the car. i noticed a month or two ago that it seemed the clutch was slipping in every gear. tried playing...

i have a metco #2 lower, upper setting, billitflow pulley set with 100mm idler, billitflow 2.76 on s.c. also, i did notch the tensioner ! i know there are 100+ people out there running the same set up ! what is the gates belt size please??? i checked cobra bobs site & billetflow, witch say 2...

i have a metco #2 lower, upper setting, billitflow pulley set with 100mm idler, billitflow 2.76 on s.c. also, i did notch the tensioner ! i know there are 100+ people out there running the same set up ! what is the gates belt size please??? i checked cobra bobs site & billetflow, witch say 2...

Hey guys, ripped one off pulling in my garage ! I tried to mess with getting the other off yesterday, wasn't as easy as i thought ? Anyone know a secret to getting them off, besides bringing my car in the garage the other way !!!lol !! Let me know, thanks a lot !!

hey guys, just got a AFCO H/E, i want to stencil SVT on it. does anyone have there old stencil they used when they did there's ?? also, what paint should i use, one that's rated for heat ? glossy, flat ? what size, do i center it perfectly, should i do it on the car, or off... ect. ??? i...

i got the notice for emissions today, i have always had new cars, so never had to go. i did buy cats with my bassani exhaust, but i didnt put them on. should i ?? any suggestions on anything i should do before i go ?? i just have 60lb injectors, BAP, MAF, stage 5 port, H.E. & accufab throttle...

hey guys, im putting my blower back on, i got a new gasket, should i put any kind of gasket sealant on the manifold, before bolting it back down ??? i understand this may be a stupid question to some people. i am not a mechanic, this is the first time i have taken anything apart, and actually...

hey guys, i seen a terminator the other day in a parking lot, looked inside and he had SVT embroidered on the headrests. it was done in a stitch or fabric that almost matched the grey in the seats perfect, looked great, nice and thick ! does anyone know a person or a place that does this ??? i...

hey, anyone know a place where i can get a few small parts chromed, good, but reasonable ????? haven't heard anything good about any local shops by me....let me know, thanks guys !!!

putting it back together ! those fragile bolts i broke 1 taking off, what are the torque specs for putting it back on ??? anyone know ???? its a stock eaton....

im looking to get the radiator cover for my cobra....witch ones do you guys have ? what do you think looks the best. i know there close, buy not the same ! any one have pics of both installed on there cars ??? to help me out with my decision ? any of the two, harder ti install, or both pretty...

im looking for the torque specs for the supercharger bolts on to the manifold. also, the specs on the lower pully dampener. i am putting a # 2 metco pully on, and need to know how tight for the 14mm hex nut. does anyone know where i can get all the torque specs ? there has to be somewhere that...

i know everyone has there own opinion, and thats why i like this site ! i have a newly ported eaton & i know i should not use the stock heat exchanger. what brand do you have ? 2. does one brand fit better than another ? 3. can you have a radiator one brand and the heat exchanger another ...