I am looking to sell my 03 cobra. I don't drive it anymore since I took a new job and have a 6 month old baby. I'm gonna sell this car and buy a motorcycle that can sit in my garage, it takes up less room than the cobra lol. The car has 34,xxx miles, I bought it with 31,xxx. I'm asking 20,000...
Anyone have a catted xpipe laying around that they want to get rid of. Emissions is coming up, and I have straight pipes... Last time I had a guy tack weld some heat shields on to my pipes, but they flew off the next day.
so i am about to put on my ported blower with my 60# injectors, and BAP. my question is, is the 4lb lower setup necessary. right now my car makes just shy of 500/500 with a pulley, full exhaust, and a larger heat exchanger. im not looking to compete with guys that have twin screws, but my...
so i am about to put on my ported blower with my 60# injectors, and BAP. my question is, is the 4lb lower setup necessary. right now my car makes just shy of 500/500 with a pulley, full exhaust, and a larger heat exchanger. im not looking to compete with guys that have twin screws, but my...
Hey guys, a buddy of mine has an sti down inhoiston and wants to get a tune. I told him I would ask you guys if anyone had a good or bad reputation and an AWD dyno. Trying to point him in the right direction, next stop is to get him into a ford, thanks for your input!
so, ive gotten real handy with my rotary, bt still cant seem to get it absolutely perfect. ive done everyhting i can to finish it off with 100% correction, but i just cant do it in a pheasable amount of time. i have pictures of both rotary finishing, and rotary start, with PC finishing. i...
looking to buy the following items for my 03 cobra
60# injectors plug in version (pending buy)
KB BAP still need this plus wiring upgrade kit
MAFia (pending buy)
im going to be looking for the next week or so before i buy new pm me if you have it for sale
so ill eventually be putting a twin screw on my car. i have an 03 cobra, which has straight pipes, an intake, and a 2.76 pulley. for fuel upgrades, can i buy a BAP, 60's and a mafia, and be ready for a twin screw? and as far as the BAP goes, does it matter whether or not it is a 20amp or 40...
so i was polishing my dads truck the other day outside, it was 55 degrees, low humidity, and sunny. i was using my makita rotary with pfw pads. the m105 was gumming up so bad i had to use a differnt product. even with the pad sprayed, the panel sprayed, and trying to use more product...
so, it about time to be able to go outside again in the northeast. i personally love the look of KAIO's candy shell on my black cobra. for the experts, could i put something like collinite 845 on top of the KAIO, or is there no rweason to, or is it just a wasted step. the car never sees rain...
i took my car out the other day to have a stereo put in, but i noticed that the clutch is grabbing at the top of the pedal now, where it wasnt before i put it in storage. i drove it pretty hard at the end of summer, and when i took it home the other day, i felt like a bit of pwer was lost...
so, my basement flooded, and all of my pads for my rotary got toasted, and the backing plate crumbled because they were all wet for a while with mildew etc... so, any suggestions about the size of the pads i should be using. i can remember if the previous bunch were 7 ort 8.5. what do the...
im trying to get a census of everyones favorite compound. the strongest i have is the OP II from optimum, and PB SSR 2.5. i would like something that is strong, but not dusty. using optimum polishes makes me hate the SSR bottles i have. i dont care about price, mostly concerned with ease of...
so i got the makita 9227c with the 6 inch backing plate. i used all of the previous pads i had from my PC which were the lake country orange and white.
At first i tried to cut with an orange pad and optimum polish II, which was next to useless. Then i went to the orange pad and PB SSR...