I may have to sell my 04 Cobra. I will entertain offers. I am not happy about this decisision, but it is what it is. It is perfect.
My sig lists many of the mods but leaves out alot.
It is currently setup for 21lb sboost but I may drop it back to 17 to run on pump gas. 4lb lower w/2.93 upper...
This is a set of perfect Diamond Racing Wheels in black (Joe Lynch Specials) for an 03/04 Cobra with IRS. They have a almost new set of M&H Cheater Slicks. I made 2 runs only with them and drove them 75 miles to the track only. I will include the special lug nuts. $400 + Shipping. Local pick up...
These have 10 runs on them only. They were my 2nd set and I switched to another tire so you can have these for a good price. $200 local pickup or $250 shipped
These are my origional Factory front wheels from my 2004 Cobra in chrome 17x9 with Goodyear F1's with 7500 miles on them and they are in excellent shape and a set of AFS Replica wheels in 18x10.5 with an almost new set of BFG 315x30x18 Drag Radials. I have never raced with these tires. The rear...
This is a set of perfect Diamond Racing Wheels in black (Joe Lynch Specials) for an 03/04 Cobra with IRS. They have a almost new set of M&H Cheater Slicks. I made 2 runs only with them and drove them 75 miles to the track only. I will include the special lug nuts. $400 + Shipping. Local pick up...
I am ready to get a cage installed. I am aware of Rhodes (they are 2 hrs from me) but am wondering if there is anyone else in the Maryland area that does a decent cage for out cars. I prefer moly and want swing out doors, pads, belts. I want to take the car and pick it up. I do not want to...
I am ready to get a cage installed. I am aware of Rhodes (they are 2 hrs from me) but am wondering if there is anyone else in the Maryland area that does a decent cage for out cars. I prefer moly and want swing out doors, pads, belts. I want to take the car and pick it up. I do not want to...
Whatever you do replace the junk stock idlers. I was stupid and did not believe the crap that they fail. (I never had one fail on my Lightning in 30k miles with a 5lb lower) and my Cobra in 8000 miles. I Installed a 4lb lower, made 2 runs at the track and maybe 2 or 3 street runs in 2nd-thru 3rd...
I would like to remove the ABS unit as it looks real heavy and mine is bad anyway (ABS failure code). Has anyone made up or had made up the necessary brake lines.
I want to relate a service experience between myself, my 2004 Cobra and Woodbine Motor Sports in Woodbine Maryland. This is what I call exceptional service that is rare to find these days.
I had been planning to go to SSOTN todaty (rained out) so the timing of this story is relevant.
I...
I wanted to stiffen the engine mounts up some to reduce torque flex during the 1-2 shift (occassionaly miss a gear). I am told the urethane travel limiter type are not durable and that the solids are fine. I thought the solids were for track only and the vibration and lack of flex was too...
I am building a new short block after burning a hole in a piston on my 04 Cobra.
This is what I have and am wondering what steps I should ask the machine shop to do.
Stock crank and rods are OK
New Ford Block
New Diamond 15cc dish pistons .020 over with ceramic top and lube side coating to...
Has anyone heard of the TMD H or I Beam rods for the CoObra? They look like and sound like (spec wise) like the Manley or Eagle rods with the arp2000 bolts?
I hurt my motor this past weekend. Probably pistons. No noises, lost power, white smoke, pass side plugs black and oily, signs of detonation.
I will want the engine R&R'd, Engine dissasembled, inspected (crank, block, rods, etc,) bored, balanced, new pistons, rings, bearings, ARP studs and rod...