Recent content by turbosaleen

Accufab built an engine for a Ford GT (twin turbo) for a customer, Ray Hoffman, and Heffner Performance installed it in the car. Ray sent a private plane to pick John mihovetz up last Thursday and fly him to Miami to do his "MoTec Magic" on the car for the Miami Mile (standing start for a mile)...

Forged crank forged h beam rods and forged pistons .. 5 angel valve job on heads and ford gt cams installed with valve springs setup for them and up to 25 psi boost complete asembled long block with stock blower fuel rails and injectors. I also have the ford efi system complete brand new...

stock crank .. aftermarket rods and forged pistons .. 5 angel valve job on heads and ford gt cams installed complete asembled engine minus the ac power steering, valve covers and alternator. comes with the stock blower includes the stock fuel rail and injectors. I also have the ford...

wow what a pile ran across a yello henessy superchared 2010 camaro in a 08 gt 500 Every singel time he shifted it over 2500 rpm it would back fire like hell .. i dont mean a exhaust burble i mean a omfg what idiot tuned that car back fire BANG. I must say the guy driving it < probly...

we took this 1969 camaro down nut and bolt and did a full reso mod build in 60 days. some work as its being performed. powder coated subframe the front subframe installed with brakes and the painted fire wall the under side of the car is fully body worked and painted as the top is...

big bore ford motorsport boss block all the best parts custom pistons by JE not off the shelf units with taper wall tool steel wrist pins and custom ring lands pistons are custom for a 3v with big cams but will work fine with a 4v with stock cams or mild cams. eagle 4340...

big bore ford motorsport boss block all the best parts custom pistons by JE not off the shelf units with taper wall tool steel wrist pins and custom ring lands eagle 4340 stroker crank shaft eagle h beam rod with arp 2000 rod bolt up grade the short block was...

bought this car off a auction it was slid into a curb bending two wheels and messing up the passenger side skirt.. the complete repair involved was as follows new passenger side skirt new irs cradle < bushing was torn in stock one so i got new unused one from ebay from panoz motorsports...

got a few things done finished up the drive by wire pedal mount, the passenger header, the motor and trany mounts, the radiator overflow and hose setup < it uses all stock 500 hoses so replacement parts will be easy > , finished up the master cylinder mount by making abillet plate to move it out...

the engine the front suspension hiedts ifs 2 with coilovers and wilwood 12 inch polished caliper brakes all powder coated in silver vein The rear suspension going in. also powder coated in silver vien \ forgive the areas that look white or dirty thats some run off from the...

hand built all steel wide body kit going to get a 427 ls-1 with a procharger. 305 30 19 FRONT tires 345 25 20 rears

horsepower freeks bmw m3 turbo 700 + rwhp he got a good jump because i couldnt hear his horn so i didnt get on it till he had a good car rolling start he pulls me through third while im spinning i stop the pull at the end of third when i hook up then he puts another car when i shift...

hmm well lets see i got a 2500 horsepower engine ... and i do have a mini tubed 66 mustang that will fit a 15 inch wide drag radial and weigh about 2750 pounds with that motor :) anyone know of a standard that can take 1600 + rear wheel torque and 1900+ rwhp :) prety sure it would destroy...

im building a 325 big bore stroker and switching to a 3.3 whipple on my 05 so im selling my kb kit Kit in cludes over 2000 in custom aditions Sheet metal rear intake custom big bore inlet tube with 115 mm mass air also will come with customers choice of boost levels 10-12 being all i would...

-------------------------------------------------------------------------------- im building a 325 big bore stroker and switching to a 3.3 whipple on my 05 so im selling my kb kit Kit in cludes over 2000 in custom aditions Sheet metal rear intake custom big bore inlet tube with 115 mm...